Advertisement
Quick Links
Introduction
Purpose
This manual provides instructions to install the Lower Front Totalizer Retrofit Kit for Atlas
9100 Series Units (M05813K004).
Note: A new Bezel with a totalizer opening may be required when installing the kit. Use
Table of Contents
Topic
Introduction
Important Safety Information
Installation of the Lower Totalizer Retrofit Kit
Required Tools
The following tools are required for the installation of the kit:
• Phillips
• Wrench
• Hammer and Punch
Parts List
The following table lists the parts included in this kit.
Item
1
2
3
4
5
6
7
8
9
10
MDE-4809 Atlas™ 9100 Series Totalizer Retrofit Kit (M05813K004) Installation Instructions · May 2009
templates to identify the correct Bezel.
Screwdriver
®
Description
Face Dial Blank Totalizer
Nut Hex Keps W/EXT LW 6
SCR SLF V/R 510500-325
Modified Gear Plate Assy
Totalizer 8 WH VR 370016
SCR V/R 510500-327
Totalizer Seal V/R 28698K
INSTR-9100 Series Front T
8 X 10 X 4 200#C.K. R.S.
CRTN 25-3/4X9-3/4X6-1/8 R
Atlas
9100 Series Totalizer Retrofit Kit
™
(M05813K004) Installation Instructions
Page
1
3
5
Part Number
Quantity
025548
1
Q12068-02
10
S00702
1
015891
1
S65336
1
S00704
2
S00207
2
032933
1
018072
1
018116
1
MDE-4809
May 2009
™
Page 1
Advertisement
Related Manuals for Gasboy Atlas 9100 series
Summary of Contents for Gasboy Atlas 9100 series
- Page 1 MDE-4809 Atlas 9100 Series Totalizer Retrofit Kit ™ (M05813K004) Installation Instructions May 2009 Introduction Purpose This manual provides instructions to install the Lower Front Totalizer Retrofit Kit for Atlas ™ 9100 Series Units (M05813K004). Note: A new Bezel with a totalizer opening may be required when installing the kit. Use templates to identify the correct Bezel.
- Page 2 Introduction Warranty For information on warranty, refer to MDE-4255 Gasboy’s Warranty Policy Statement. If you have any warranty-related questions, contact Gasboy’s Warranty Department at its Greensboro location. Page 2 MDE-4809 Atlas™ 9100 Series Totalizer Retrofit Kit (M05813K004) Installation Instructions · May 2009...
- Page 3 Gasboy Authorized manual, where additional hazards and safety precautions for Service Contractor or call the Gasboy Service Center at 1- your task will be found. Fire, explosion, electrical shock or 800-444-5529. It is imperative to your safety and the safety of pressure release could occur and cause death or serious others to understand the procedures before beginning work.
- Page 4 Important Safety Information No Open Fire In an Emergency Inform Emergency Personnel Open flames from matches, lighters, welding Compile the following information and inform emergency torches or other sources can ignite fuels and their vapors. personnel: • Location of accident (for example, address, front/back of building, and so on) No Sparks - No Smoking •...
- Page 5 IMPORTANT INFORMATION Read all important warnings and safety information prior to working on units. To install the Lower Front Totalizer Retrofit Kit for Atlas 9100 Series Units (M05813K004), proceed as follows: Remove the existing dial face. Retain the screws for later use.
- Page 6 Installation of the Lower Totalizer Retrofit Kit Remove the two screws that secure the totalizer, using a wrench. Figure 2: Removing the Screws Remove the totalizer from the register assembly. On the opposite or the front side of the non-computer, remove the two screws and bracket from the lower totalizer position.
- Page 7 Installation of the Lower Totalizer Retrofit Kit Install the slotted gear plate, using the bolt provided in the kit. Note: Hold the gear plate while tightening the bolt to ensure that the gearing turns smoothly. Figure 4: Installing the Slotted Gear Plate (ii) Slotted Gear Plate Bolt...
- Page 8 New Seal Cap Totalizer Install the new dial face, using the screws removed in step 1. This completes the installation of the Lower Front Totalizer Retrofit Kit for Atlas 9100 Series Units. Atlas is a trademark of Gasboy International. Phillips is a registered trademark of The Phillips Screw Co.