Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for dicodes Dani Box V2
Summary of Contents for dicodes Dani Box V2
- Page 1 Dani Box V2 Dani Box Mini manual...
- Page 2 24mm and smaller. Mechanically the Dani Box V2 is identical to the former Dani Box (V1) and the difference between Dani Box V2 and Dani Box Mini is the form factor. The Mini was designed to attract users, who prefer very small devices.
- Page 3 02 Feature List - 5 to 80W with one Li-Ion battery size 18650 - Adjustable battery discharge level (2.5-3V) - Up to 11V output voltage - Up to 22A output current - System source resistance determination - Temperature controlled vaping mode with various wire-types - Mechanical MOD mode - 10 Power boost modes - 10 Heater protection modes...
- Page 4 03 Display Operation The mods are equipped with a graphical OLED display which provides all impor- tant information about the status during and for 4 seconds after each vape. Temperature controlled mode: Battery-voltage during Temperature during vape the vape, including voltage Other modes: battery symbol drop.
- Page 5 “Hello” and the user is led to the main menu. For actively switching off the mod the fire button is to be pressed shortly 5 times and the display shows “Bye..” Important Note: The dicodes boxmods differentiate between active switch off and the automatic switch off after the switch-off-time. When the mod was switched off...
- Page 6 For further information about this topic, please read the “Appication Note for Temperature Controlled Vaping”, available on the dicodes-mods website. Coil Resistance and Coil Temperature This is a display only menu item. The coil resistance is displayed in a range from 0.00 to 9.90 Ohms.
- Page 7 The systems source resistance is the sum of the batteries inner resistance as the main contribution and all contact and wiring resistances of the device. As already stated, typical battery resistances vary from 18m to 80m depending on the type. The typical contact and wiring resistance of the dicodes boxes sum up to about 6m .
- Page 8 05 Main Menu (Page 4) Notes about very high power vaping When vaping at high power it is strongly recommended that only the best in class batteries are used and that all contacts are kept clean. Always keep in mind that 80W taken even from a high drain battery wil create power losses in the batteries inner resistance as well as at all mechanical contacts, which finally will reduce the total vape time and lead to volt drop.
- Page 9 “TempCof”. The range for the coefficient is 050 to 650. If you use the dicodes wire (RESISTHERM) it is guaranteed that the wire will always have the same coefficient, because the wire was especially designed for temperature regulation purposes. The regulation accuracy is best then, as the combination of resistivity and high coefficient is very good.
- Page 10 05 Main Menu (Page 6) 2. Heater Protection Mode (only when Expert Mode=1) Main Menu The heater protection mode is a periodic interruption of the power applied to the coil. The duration and the repetition rate of the interrupts is selected by means of the para- meter “Heater Prot”...
- Page 11 0 OvrVolt: The input voltage is too high. The are prepared for the use of one battery. dicodes Dani Boxes If the input voltage exceeds 4.5V this error message is displayed. Reduce the input voltage to the specified range. 1 ChkAtom: No atomizer detected or open coil.
- Page 12 (*1 ) The temperature coefficient selects the type of wire material in the range 050 to 650: When TC-mode is selected (Main menu HCtrl=1), the user must select the wire type to be NiFe30 (320, dicodes wire), Ni200 (620), Titanium (350), SS304 (105, V2A), SS316 (88), SS316L (92), NiFe48 (480) or “Other”. The value for “Other” is adjusted here.
- Page 13 “Power”. The power limitation makes sense especially in the power vaping mode to reduce the range to the used atomizer. All dicodes devices have a functionality to adjust the minimum discharge level of the battery between 2.5V and 3.0V (older models 3.5V). Almost all available batteries on the market specify the minmum discharge level of 2.5V to 2.7V.
- Page 14 5 different modes. But in order to keep the menu dicodes Dani Boxes as short and simple as possible, 3 of the 5 modes are only available, if the Expert-Mode is set to 1. The name is Expert-Mode, because the use of the additional operation modes requires additional knowledge about their functionality.
- Page 15 06 Extended Functions Menu Additional Explanation to several menu items, page 3 The Extended Functions Menu has another sub-menu showing several statistical values. There are two types of value-counters, either re-settable to zero or not. The statistic counters are saved whenever the mod is automatically or manually switched off.
- Page 16 In case the device shows a permanent electric fail or if a software bug is detected, the user is free to send the device back to dicodes for repair without cost. The customer is requested to check the devices housing for scratches or marks, prior to any use.
- Page 17 Friedrich der Große 70 D-44628 Herne Germany Phone: +49 2323 1463635 Email: info@dicodes-mods.de Web: www.dicodes-mods.de Errors excepted. Subject to technical or other changes without prior notice. c copyrights dicodes GmbH, Germany, no unauthorized reprint. 10.04.2018 dicodes Dani Boxes manual, ENG, revision 1...
Need help?
Do you have a question about the Dani Box V2 and is the answer not in the manual?
Questions and answers