Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Q5X QT-300
Summary of Contents for Q5X QT-300
- Page 1 QT‐300 Module User Manual Rev: 1 ...
- Page 2 QT‐300 Revision: 1 History Rev 1 January 2, 2018 Original QT‐300 User Manual Page 2 of 11 Q5X Systems, Inc. 2018 ...
-
Page 3: Fcc Notices
— Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications not expressly approved by Quantum5X Systems Inc, could void the user’s authority to operate the equipment. QT‐300 User Manual Page 3 of 11 Q5X Systems, Inc. 2018 ... -
Page 4: Innovation, Science And Economic Development Canada (Ised)
Approved antenna and connectors Antenna / Connector Manufacture Connector Type Max Gain Type Integrated Antenna Q5X NA 3dBi SSMA Whip Antenna Sam Woo Electronics SSMA 0 dB This device operates on a no-protection, no-interference basis. Should the user seek to obtain protection from other radio services operating in the same TV bands, a radio licence is required. -
Page 5: Rf Exposure Compliance
Sciences et Développement économique Canada. RF Exposure Compliance: The QT-300 Module is granted with a modular approval for mixed mobile and portable applications. module is to be used by Quantum5X in their final products without additional FCC/ISED (Innovation, Science and Economic Development Canada) certification if they meet the following conditions. - Page 6 QT‐300 Revision: 1 Module Integration into Host End Products The QT‐300 Module Transmitter has been designed by Quantum5X Systems Inc. to be used by Quantum5X as a building block for their wireless audio transmitter products. The module, as designed, is a standalone unit that is ready for integration into final form factor with the limitation for mobile use as specified in RF Exposure compliance. For proper usage of the module, the module integrator must ensure that the input power and input audio signal do not exceed the specified limits as outlined in the specification section. Failure to do so will result in damage to the module. Final product(s) after integration with this module shall be tested to comply with all applicable FCC requirements and Unintentional radiators (FCC section 15.107, 15.109 and ISED ICES‐003) before declaring compliance to Part 15 of the FCC Rules and ISED ICES‐003. The module integrator may not: 1) Alter, modify or remove the module case. 2) Make changes to the Circuit Card Assembly of the module. Failure to comply with these restrictions will result in violation of the FCC certification. Labeling of the End Products: The modular transmitter must be equipped with either a permanently affixed label. The modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: ‘‘Contains Transmitter Module” or ‘‘Contains “. Any similar wording that expresses the same meaning may be used. Below are Sample Module and Product lables that must be used for the Module and the Product. QT‐300 User Manual Page 6 of 11 Q5X Systems, Inc. 2018 ...
- Page 7 SEL for programming. The frequencies are programmed by using the 16‐position dial and the SEL (select) button. The LED shows the current menu, the charge status, the battery status and the operating status. Overview The QT‐300 has multiple parameters that can be changed in different menus. A combination of the SEL (select) button and the adjacent Alpha Numeric 16 position dial are used to access and make changes to the various device parameters. The table below outlines each menu: Menu Input Action SET FREQ ‘A’ ‐ Single press Allows user to Set the 6 frequency digits. READ FREQ ‘B’ ‐ Single press Reads the 6 digits of the tuned frequency. SET PWR ‘C’‐ Single press Allows user to Set RF output power level. READ PWR ‘D’ ‐ Single press Reads the current RF output power level. READ BATT ‘E’ ‐ Single press Reads the current battery percentage. READ FW VER ‘E’ ‐ Double press Reads the Firmware Version ‘F’ ‐ Unused Reserved for additional feature. Powering On To operate the transmitter, press and hold the SEL/PWR button for 5 seconds. The LED will flash red then illuminates green to indicate the transmitter has powered on. After a short delay, the color of this LED will reflect the current battery level color. QT‐300 User Manual Page 7 of 11 Q5X Systems, Inc. 2018 ...
-
Page 8: Battery Level
Battery Level If the LED is illuminated Green, the battery is full (100% – 66%) approx. 8 – 5 hr. If the LED is illuminated Orange, the battery is half empty (66% – 33%) approx. 5 – 3 hr. If the LED is illuminated Red, the battery is nearly empty (33% – 0%) approx. 3 – 0 hr. At full charge the QT‐300 will operate for approximately 8 hours at 100mw of RF power. A finer measurement of the remaining battery life is available under menu item E. Set Frequency To change the frequency, the six digits of the desired frequency must be entered. To enter the frequency programming mode, turn the dial to position ‘A’ and press the SEL button. The LED will begin single Red flashes to indicate you are now editing the first digit of the frequency setting. The first set of numbers (470.XXX) will be indicated by Single Flashes the second set (XXX.025) by Double Flashes. Single Flash = SF Double Flash = DF Rapid Flash = error ‐ a rapid Red Flash indicates the first digit is wrong, it can only be 4, 5, or 6. If it's a rapid Green Flash then the second digit is out of range, etc. To program in 470.025 Mhz, turn the dial to position ‘A’, press the SEL button, then do the following; Red ‐ SF ‐ turn dial to 5 ‐ press SEL button Green ‐ SF ‐ turn dial to 7 ‐ press SEL button Orange ‐ SF ‐ turn dial to 5 ‐ press SEL button ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ Red ‐ DF ‐ turn dial to 0 ‐ press SEL button Green ‐ DF ‐ turn dial to 2 ‐ press SEL button Orange ‐ DF ‐ turn dial to 5 ‐ press SEL button The last SEL button press completes the programming steps and the new frequency is set. The LED will resume displaying the battery status and the transmitter is now operating on the new frequency. If the user inputs a number that is not within the tunable range or is not a 25 kHz step, the transmitter will not allow the user to proceed until a valid number is input. Upon entry of an incorrect digit, the LED blink pattern will change to a rapid flash in the color of the current digit being edited. To continue, the user must select a valid number on the dial and press the SEL button again. QT‐300 User Manual Page 8 of 11 Q5X Systems, Inc. 2018 ... -
Page 9: Display Frequency
After a short pause, the LED will flash Green 7 times to indicate the second digit is 7. After a short pause, the LED will flash Orange 5 times to indicate the third digit is 5. After a short pause, the LED will be solid Red for 1 second to indicate the fourth digit is 0. After a short pause, the LED will flash Green 2 times to indicate the fifth digit is 2. After a short pause, the LED will flash Orange 5 times to indicate the third digit is 5. Once the sixth digit has been displayed, the LED will resume displaying the battery status. Set Output Power To set the output power, turn the dial to the letter ‘C’ and press the SEL button. The LED will begin flashing triple Red Flashes to indicate you are now editing the output power. There are 5 different output power levels that can be set: 10 mW, 25 mW, 50 mW, 100 mW and 250 mW for North American Standard Mode or 3 difference level that can be set: 10 mW, 25 mW, 50 mW for European Mode. To set the output power to 100mW, turn the dial to 4 and press Output Power Entered Value the SEL button. 10mW 1 When the SEL button is pressed, the new RF Output Power will be 25mW 2 programmed and the LED will then resume displaying the battery status. 50mW 3 100mW 4 250mW 5 QT‐300 User Manual Page 9 of 11 Q5X Systems, Inc. 2018 ... -
Page 10: Display Firmware Version
QT‐300 Revision: 1 Display Output Power To display the output power, turn the dial to the letter ‘D’ and press the SEL button. The Red LED will flash the number that is related to the output power. For example, if the output power is set to 100mW, the LED will flash Red 4 times. Battery Level To display the current battery level, turn the dial to the letter ‘E’ and press the SEL button. The LED will blink red 1 to 10 times. 10 blinks indicate 100% battery remaining and 1 blink indicates 10% battery remaining. Display Firmware Version To view the current firmware version, turn the dial to the letter ‘E’ and double press the SEL button. The LED will display the 3 digits of the current firmware version. For example, the firmware version is 0.2.2. The LED will turn on Red solid for 1 second to indicate the first digit is 0. After a short pause, the LED will flash Green 2 times to indicate the second digit is 2. After a short pause, the LED will flash Orange 2 times to indicate the third digit is 2. Once the third digit has been displayed, the LED will resume displaying the battery status after a short pause. Mic Gain There is a Mic dial on the left side of the QT‐300 that has a range of ‐20 dB to +20 dB. To increase the Microphone gain, turn the dial clock‐wise. To decrease the Mic gain, turn the dial counter‐clock‐wise. 0 dB is located at the mid‐point of the dial and is indicated on the case. Powering Off To power off the device, press and hold the SEL button for 5 seconds. The LED will turn red then off to indicate the device has been powered off. QT‐300 User Manual Page 10 of 11 Q5X Systems, Inc. 2018 ... -
Page 11: Specifications
Technical Data UHF Radio RF Carrier Frequency Range: 525 – 600 MHz Working Range – 500m (line of sight, outdoors for a single system) Note: Actual working range depends on RF signal absorption, reflection and interference Antenna impedance: 50 Ω Impedance RF Power Output: see table below Item # Product Name Max RF Power 1 QT‐300 Module 250 mw 2 PlayerMic (Body Mounted Only) 100 mw 4 AquaMic (Body Mounted Only) 250 mw 7 Incognito (Body and head Mounted) 100 mw 9 BeltMic (Body Mounted Only) 250 mw Antenna impedance: 50 Ω Impedance Technical Data QT‐300 Module Power Requirements: 3.7V Current Drain: 140 mA Max Input Audio Signal: 1 VRMS Audio Gain Adjustment Range: ‐20 dB – 20 dB Overall Dimensions: 31mmX12.9mmx52mm (Battery on top of module) Net Weight: depends on model QT‐300 User Manual Page 11 of 11 Q5X Systems, Inc. 2018 ...