Advertisement
Safety First!
CAUTION! – Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation exposure.
This laser product is certified as a Class IIIa laser product to the
requirements of the US Federal Laser Product Performance Standard (FLPPS)
contained in the regulations in 21 CFR Subchapter J. Class IIIa laser products
can be hazardous when directly viewed.
Avoid direct viewing of Class IIIa laser energy. For reference the FLPPS
requirements for demonstration laser products like laser pointers are limited to
Class IIIa levels of laser energy. This product uses diffractive optics to scatter the
beam energy. This scattering effect causes the energy concentration to drop
below the exposure limits for momentary or accidental viewing at a relatively short
distance from the laser aperture. As similar with all bright light sources, when you
operate this device in unsupervised general public areas, it is recommended that
up-close access to the Elf Light be restricted or prevented.
This laser display device incorporates a Class IIIa laser system which, by itself,
may be hazardous. However, this laser display device incorporates a protective
housing and diffractive holographic optics in the machine's design such that there
is no exposure or human access to the laser radiation during operation or
maintenance above the Class IIIa limits. Each individual laser beam's power is
less than 5mW, which is about an average laser pointer.
UNDER NO CIRCUMSTANCE shall attempts be made to open the protective
housing or operate the device if the aperture windows are damaged. All service
to this laser display device requiring the protective housing to be opened and/or
removed shall be performed by a Elf Light service personnel or their authorized
agents. No user-serviceable parts - opening the Elf Light protective housing voids
the warranty.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the product.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This device complies with Industry Canada Incense-exempt RSS-210. Operation
is subject to the following two conditions: (1) this device may not cause interfer-
ence, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Techno Source, A Division of LF Products, Pte Ltd, A Li & Fung Company
20 West 22nd St., Suite 1101, New York, NY 10010
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
(2)
Troubleshooting Guide
Problem
Possible Cause
No light coming
1. Remote control not
from unit
working or timer is on
2. Electrical connection
3. Outlet not working
4. Not within operating
temperature range
Dim or flickering
1. Not within operating
light
temperature range
2. Unit is connected to a
dimmer
3. Improper power
4. Debris on aperture
glass
1. The green light is
One color
much brighter than
appears dimmer
the red
than the other
2. Some surfaces may
(if more than
absorb certain colors
one color)
of light causing it to
appear dim or
non-existent
Remote not
1. Battery is sealed in
working or
in protective plastic.
operating
2. Remote batteries
erratically
exhausted or
positioned improperly
3. Remote out of range
of communication
interference
4. Remote is not paired
with projector
(7)
PAGE 7
Remedy
1. Unplug the light and plug back in (the
Elf Light will reset to default and should
turn ON when plugged in).
2. Check entire length of electrical cord for
breaks in the wire and connections on
both the projector and transformer.
3. Check to make sure there is power to
the electrical outlet supplying 120VAC at
60Hz. Use included transformer only.
4. Operate unit within -15° F to 90° F.
If below -15° F, leave unit on for at least
30 minutes until it warms up to operating
temperature.
1. Operate unit within -15° F to 90° F.
If below -15° F, leave unit on for at least
30 minutes until it warms up to operating
temperature.
2. Do not use with a dimmer.
3. Check to make sure there is power to
the electrical outlet supplying 120VAC at
60Hz. Use included transformer only.
4. Clear aperture glass of any debris.
1. The human eye is most sensitive to
green light and less sensitive to other
colors. This is normal.
2. Position the projector to another surface
for better effect. Brighter colored
surfaces work best. Objects such as
green foliage may absorb red light.
1. Open back and remove protective
shrink wrap. Place back in Remote.
2. Check LED indication on the remote by
pressing any button. If the LED is not
working, then replace the batteries with
a fresh 23A cell aligning the "+" side of
the battery with the "+" side of the
remote control.
3. Extend the antenna on the remote for
maximum range or move closer to the
projector. Please note that overhead
power lines, microwaves, wireless
routers, cordless phones and other
devices may impact the communication
between the remote and projector.
4. Unplug desired Elf Light to unpair and
follow pairing procedures on page 6.
Advertisement
