Using calman with direct lut upload capability (4 pages)
Summary of Contents for Flanders Scientific Inc. XM310K
Page 1
Monitor User Manual Updated 09.25.2018 XM Series XM310K This manual is based on firmware V1.1.38. Some selections may be unavailable or not work correctly if using a different firmware build. Flanders Scientific, Inc. 6215 Shiloh Crossing Suite G Alpharetta, GA. 30005 Phone: +1.678.835.4934...
Safety Precautions CAUTION DO NOT LAY FLAT. DO NOT ROTATE OR TURN UPSIDE DOWN. Monitor must be transported, stored, and operated upright at all times. Please ensure monitor is kept clean and free of dust. Failure to follow these guidelines may lead to dust inflow or panel damage. Panel bending, bruising, and dust inflow are not warrantable conditions.
Page 4
Safety Precautions • For proper screen maintenance please follow the guidelines below to prevent scratches, discoloration, or other damage to the panel: • Avoid striking the screen with any object. • Do not wipe screen hard. Apply only gentle pressure if cleaning. •...
Page 5
Parts & Their Functions Keyboard • SDI 1: Used to select SDI Input 1 as the active Input. • SDI 2: Used to select SDI Input 2 as the active Input. • SDI 3: Used to select SDI Input 3 as the active Input. •...
Page 6
Parts & Their Functions Back Panel • SDI In: 4 Multi-Format 12G/6G/3G/HD-SDI Inputs. • SDI Out: 4 Looped 12G/6G/3G/HD-SDI Outputs. • MON Out: Processed output. Follows Mode Selection • DP In: Display Port Input. • Audio In/Out: Analog Stereo Mini-phono Au- dio Input &...
Page 7
Menu Navigating the Menu Pressing the MENU button on the monitor’s keypad will call up the on screen menu. To navigate use the UP and DOWN buttons and press the ENTER button to select the highlighted sub menu. Navigate the sub menu in the same way by using the UP and DOWN buttons to highlight a particular function and press ENTER to change that function’s settings.
Page 8
Menu - Scope Menu Scope Menu Function Luminance Scope Lum Position Bottom Right Video Vector Color Vec Position Bottom Right System Area Marker Safety Marker Center Marker Lum & Vec Position Use Lum & Vec Position to select in what area of the screen you would like your Scopes to be displayed. Area Marker Use the Area Marker function to select what type of marker is displayed when the marker function is active.
Page 9
Menu - Video Menu Video Menu Function Input SDI 1 Scope Mode AUTO Video SDI Format AUTO Color System SDI Format Select the correct incoming signal format. SDI Format selection overrides payload ID if not set to AUTO. Mode The mode selection allows you to set the SDI input configuration as well as the processed monitor output configuration.
Page 10
Menu - Color Menu Color Menu Function ColorSystem User Scope LUT Mode Normal Video Range 64-940 Color Gamut BT.709 System Temperature Default EOTF Gamma 2.4 ColorSystem The CINECOLOR system setting is currently supported for HDR / dynamic backlight use. USER, LightSpace, CalMAN, and CINECOLOR are supported for SDR / static backlight use.
Page 11
Dynamic Motion Optimization and Dynamic Character Optimization are the two HDR compatible luminance selections that enable the XM310K’s zoned backlight array. The monitor is only in an HDR compatible configuration if both CineColor and a dynamic backlight option are enabled. All other luminance selections enable a static, always on, backlight configuration.
Page 12
Menu - Color Menu Color Menu Function ColorSystem User Scope LUT Mode Normal Video Range 64-940 Color Gamut Rec709 System Temperature Default EOTF Factory Alignment Reset This setting deletes the Factory AWB calibration. Do not use this setting unless you have the proper equipment to redo the factory AWB calibration.
Page 13
Menu - System Menu System Menu Function Update Firmware Scope Langauge English Video IP Address 192.168.1.100 Color Version 1.1.1 System Serial Number XM650A0000 Update Firmware When left to SET (default) allows firmware to be remotely updated using the FSI IP Remote Utility. When set to OFF prevents firmware from being remotely updated.
Page 14
Menu - OSD Menu OSD Menu Function Time Code Scope Menu Position Top Left Video Color System Time Code Allows you to select whether to display Time Code on screen pulled from an SDI signal. Reserved for future use, inactive in 1.1.38 Menu Position Changes position of on-screen menu.