Advertisement
Changing Battery Modes (Mio R-1 and R-2)
Conf iguration Mode
The Configuration Mode enables the user to set the battery type on the Mio R-1 and R-
2 remotes to Normal for standard AAA type batteries, or Recharge if equipped with a
Lithium Ion battery pack upgrade. To enter Configuration Mode:
Press and hold the STOP button and the INPUT button simultaneously as shown in
FIG. 4 step 1.
The two buttons must be pressed within 0.1 seconds of each other and held down for 2
seconds. The device indicates that you are now in Configuration Mode. See below for
available modes.
Battery Type
1.
Pressing button "6" on the remote toggles the displayed battery type between
Normal and Recharge. The type of battery installed in the MIO remote dictates the
battery type to be selected.
2.
Press the EXIT key shown in FIG. 4 step 3 when selection has been made and is
reflected in the display at the top of the remote.
Note: Settings will not be lost in the event the batteries die or are removed.
NORMAL
FIG. 4
REMOTE "BATTERY TYPE" PROGRAMMING FEATURES
© 2015 Harman. All rights reserved. AMX, AV FOR AN IT WORLD, and HARMAN, and their respective logos are registered trademarks of HARMAN.
Oracle, Java and any other company or brand name referenced may be trademarks/registered trademarks of their respective companies.
AMX does not assume responsibility for errors or omissions. AMX also reserves the right to alter specifications without prior notice at any time.
The AMX Warranty and Return Policy and related documents can be viewed/downloaded at www.amx.com.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax 469.624.7153
AMX (UK) LTD, AMX by HARMAN - Unit C, Auster Road, Clifton Moor, York, YO30 4GD United Kingdom • +44 1904-343-100 • www.amx.com/eu/
Last Revised: 11/05/2015
Display indicates battery type selected.
1. Press and hold the STOP and the
INPUT buttons simultaneously to
enter program mode.
3. Press the EXIT key when complete.
2. Press "6" to toggle between
Normal and Recharge in display.
Charging The Mio Remote with the Charging Base
The Mio remotes receive power for recharging the battery pack from a charging base.
To recharge the battery pack in a Mio remote, the charging base must first be installed
correctly.
1.
Locate the power cord equipped with a power brick AC/DC converter.
2.
Connect the angled barrel power connector of the power cord into the bottom
power port on the Mio remote charging base. See FIG. 5 for the location.
3.
Route the cable through the provided channel as shown so that it comes out the
side of the base. This will ensure that the base sits flush on a flat surface.
4.
Connect the AC power plug from the AC/DC converter power brick to an external
power source (wall outlet, power strip, etc.)
Note: Some power supply bricks are equipped with an LED that appears very dim
when no R-series remote is present in the base. This LED lights up brightly when a
remote is in the base and charging.
5.
Place the bottom of the Mio remote into the charging base so the contacts on the
remote are on top of the charging contacts inside the charging base. The Power
LED on the Mio remote blinks red to indicate it is charging and illuminates solid
red when it is done. Full charge cycle for a depleted battery is approximately 3
hours.
Avoid placing units equipped with AAA batteries into the charging
base.
FIG. 5
MIO REMOTE CHARGING BASE (TOP AND BOTTOM VIEW)
Rubber Feet
(Bottom View)
Angled Barrel Power Connector
(Top View)
Charging Contacts
93-0147-02
REV: F
Advertisement
