Table of Contents
Advertisement
Quick Links
User Manual
Please review before operating vac.
Wet/Dry Vacuum
MODEL P16-SQ16S
Household and Workshop Use.
Household and Workshop Use.
ATTENTION!
Read all safety rules carefully before attempting to operate.
Retain for future reference.
DANGER!
Never operate this unit when flammable materials or vapors
are present because electrical devices produce arcs or
sparks that can cause a fire or explosion. NEVER OPERATE
UNATTENDED.
When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.
WARNING -
1. Do not leave appliance when
plugged in. Unplug from outlet
when not in use and before
servicing.
2. Do not expose to rain - store
indoors.
3. Do not allow to be used as a toy.
Close attention is necessary when
used by or near children.
4. Use only as described in this
manual. Use only Manufacturer's
recommended attachments.
5. Do not use with damaged cord or
plug. If appliance is not working as
it should, has been dropped,
damaged, left outdoors or dropped
into water, contact Shop-Vac
Corporation for assistance.
6. Do Not: pull or carry by cord, use
cord as a handle, close a door on
cord or pull cord around sharp
edges or corners. Do not run
appliance over cord. Keep cord
away from heated surfaces.
SHOP-VAC AUSTRALIA PTY LTD
IMPORTANT SAFETY INSTRUCTIONS
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:
7. Do not unplug by pulling on cord.
To unplug, grasp the plug; not the
cord.
8. Do not handle plug or appliance
with wet hands.
9. Do not put any object into
openings. Do not use with any
openings blocked; keep free of
dust, lint, hair and anything that
may reduce air flow.
10. Keep hair, loose clothing, fingers
and all parts of body away from
openings and moving parts.
11. Do not pick up anything that is
burning or smoking, such as
cigarettes, matches or hot ashes.
12. Do not use without dust bag
and/or filters in place.
13. Turn off all controls before
unplugging.
14. Use extra care when cleaning on
stairs.
15. Do not use to pick up flammable or
combustible liquids such as
Patents Issued and Pending.
Advertisement
Table of Contents
Related Manuals for Shop-Vac P16-SQ16S
Summary of Contents for Shop-Vac P16-SQ16S
- Page 1 Shop-Vac 12. Do not use without dust bag Corporation for assistance. and/or filters in place. 13. Turn off all controls before 6.
- Page 2 result in foreign objects being gasoline or use in areas where blown into eyes, which can result they may be present. in eye damage. Always wear 16. Do not use your cleaner as a safety goggles when operating sprayer of flammable liquids such vacuum.
- Page 3 LIMITED TWO-YEAR WARRANTY Shop-Vac warrants the vacuum cleaner for two years from the date of purchase to correct by repair or parts replacement without charge, any product defect due to faulty material or workmanship provided that the vacuum cleaner is not used for rental service. This warranty does not cover accessories.
- Page 4 1. With cord disconnected from receptacle and tank cover removed, turn tank upside down so that the bottom is facing up. 2. Place one cotter pin in one end of the axle (Figure 1). 3. Slide on one washer (Figure 2). 4.
- Page 5 Foam sleeve and additional filters may be purchased by visiting our website at www.shopvac.com, contacting our customer service department, or purchasing at your local Shop-Vac distributor. Remove inlet deflector from the deflector guide sliding in an upward ®...
- Page 6 EMPTYING LIQUID WASTE FROM THE TANK Use special care when emptying heavily loaded tanks. Your Wet/Dry Vacuum may be emptied of waste by removing the tank cover. To empty, stop the motor and remove the plug from the wall receptacle. Remove the tank cover and deposit the liquid waste contents into a suitable drain. Your Wet/Dry Vac also comes with a convenient tank drain.
- Page 7 FOR UNITS WITH BUILT - IN RECEPTACLE 230 -240 Volt Voltage 50-60Hz 1600 Max Wattage from Motor Max Wattage from Receptacle This vacuum cleaner is equipped with a built-in electrical socket which allows a power tool (circular saw, drill, sanding machine, etc...) to be plugged directly into the cover assembly, and an automatic tool triggering feature for a clean work environment.
Need help?
Do you have a question about the P16-SQ16S and is the answer not in the manual?
Questions and answers