Advertisement
Quick Links
Cal. 5130.D
English
User's Manual
Description of the display and control buttons
Display elements
Minute hand
Date 5130.B
Hour hand
Hour and
Minute counter
Center stop-second
Alarm and reference time
Second hand
Date 5130.D
Date 5130.B
3 1
I
II
Date 5130.D
0 1
I
II
Hour counter
Push-button A
2 1
Minute counter
2 1
Push-button B
Hour counter
Center stop-second
2 1
I
II
III
Minute counter
Push-button A
2 1
III
Push-button B
Date 5130.B
Crown
1 7
I
II
Alarm time
Date 5130.D
Second hand
0 3
I
II
III
Reference time
3 1
I
Alarm time
Push-button
Note
The alarm cannot be used as long as
the chronograph is in operation.
0 4
I
II
III
Reference time
Small
minute hand
0 4
I
II
III
Reference time
2 1
Cal. 5130.B
Control buttons
2 1
Push-button A
Crown
Push-button B
Setting the date (quick mode)
Pull out the crown to position II (the watch
continues to run).
Turn the crown until the correct
date
appears.
01
Push the crown back into position I.
Please note:
The date of the following day must be set in
the calendar changing phase between 9 PM
and midnight.
Setting the date too quickly in quick mode
can result in the incorrect date being
displayed. Switching the date between
01 and 31 (position II) restores the syn-
chronisation.
Chronograph:
Accumulated timing
Example:
Start:
(start timing)
Stop:
(e.g. 15 min 5 sec following
Restart: (timing is resumed)
*
Stop:
(e.g. 10 min 5 sec following
=
25 min 10 sec
(The accumulated measured time is shown)
Reset:
The three chronograph hands are returned
to their zero positions.
Please note:
* Following
, the accumulation of the
timing can be continued by pressing
push-button A
(Restart / Stop, Restart / Stop, ...)
Adjusting the chronograph
hands to zero position
Example:
One or several chronograph hands are not
in their correct zero positions and have to be
adjusted (e.g. following a battery change).
Pull out the crown to position III (all 3
chronograph hands are in their correct
or incorrect zero position.
The display
changes from alarm time to reference
time.)
Keep push-buttons A and B depressed
simultaneously for at least 2 seconds (the
center stop-second rotates by
360° corrective mode is activated).
Setting the time and date
Example:
– Date / time on the watch:
/ 1:25 AM
17
– Present date / time:
/ 10:39 PM
04
Pull out the crown to position II (watch
continues to run).
Turn the crown until yesterday's date
appears
03
.
Pull out the crown to position III
(the second hand stops.
The display
changes from alarm time to reference
time.)
Setting the alarm time
Activate the setting mode
Press the push-button for at least
2 seconds. As soon as the
small minute
hand
jumps forward one minute, this
mode is active.
Setting
Short pressing (less than 1 second):
the alarm time is moved forward by the
minute.
Long pressing (longer than 2 seconds):
the alarm time is moved forward until the
push-button is released.
Please note:
If the push-button is not activated for
10 seconds, the setting mode of the alarm
time deactivates itself. At the same time,
two beeps are emitted to indicate that the
alarm is switched on.
Setting the reference time
*Pull out the crown to position III
(second hand stops.
The display changes
from alarm time to reference
time.)
Activating the setting mode
Press the push-button for at least
2 seconds. As soon as the
small minute
hand
jumps forwards one minute, this
mode is active.
Short pressing (less than 1 second):
the reference time is moved forwards by
the minute.
Medium pressing: (1–2 seconds):
the reference time is moved forwards by
the hour.
Long pressing (longer than 2 seconds):
the reference time is moved forwards until
the push-button is released.
Ronda aG
CH-4415 Lausen/Switzerland
www.ronda-startech.com
Battery type: 395 (diameter 9.5mm x 2.6mm / SR 927 SW)
Accuracy: +20 / -10 seconds per month
In case your watch needs to be repaired or to raise claims
under a guarantee, please contact the point of sales
Multifunction movement
The
alarm
and
chronograph
All functions can be operated with the 2 push-buttons and crown.
Initial status (chronograph hands at zero position)
– start the
chronograph
– switch the
alarm
on and off with
Chronograph active
Push-button B is also operative for the chronograph as soon as timing is
started with push-button A.
At the end of timing and when the chronograph hands are reset to the zero
positions the push-button functions once again assume their «initial status».
The alarm cannot be adjusted when the chronograph is active.
Hour counter
2 1
Minute counter
2 1
2 1
)
)
Minute counter
2 1
65,5% = 40mm Druchmesser
65,5% = 40mm Druchmesser
65,5% = 40mm Druchmesser
65,5% = 40mm Druchmesser
65,5% = 40mm Druchmesser
65,5% = 40mm Druchmesser
A
65,5% = 40mm Druchmesser
B
65,5% = 40mm Druchmesser
A
I
II
0 4
Reference time
0 4
Alarm time
3 1
Alarm time
Push-button
0 4
Alarm time
Please note:
* In order to set the time to the
exact second,
out when the second hand is in
position «60» (III).
Once the hour and minute hands
have been set,
back into position I at the exact
second.
are combined in Cal. 5130.D and 5130.B.
with
push-button A
push-button B
Chronograph: Basic function
Push-button A
(Start / Stop / Reset)
Example:
Start: Press push-button A.
Stop:
to stop the timing, press
pushbutton A once more and read
the 3 chronograph counters:
4h / 20 min / 38 sec
Zero positioning:
Press push-button B.
(The 3 chronograph hands will be reset to
their zero positions).
Note
The alarm cannot be used as long as the
chronograph is in operation.
Push-button B
Chronograph:
Push-button A
Intermediate or interval timing
Example:
Start: (start timing)
Display interval:
e.g. 10 minutes 10 seconds (timing
continues in the background)
Making up the measured time:
*
(the 3 chronograph hands are quickly
Push-button B
advanced to the ongoing measured time).
Stop: (Final time is displayed)
Reset:
The 3 chronograph hands are returned to
65,5% = 40mm Druchmesser
their zero position
Please note:
* Following
mediates can be displayed by pressing
push-button B (display interval / make up
measured time, ...)
Push-button B
Adjusting the center stop-second
A
Single step
A
Continuous
III
III
Adjusting the next hand B
Adjusting the minute counter hand
and the hour counter hand
(mechanical coupled)
A
Single step
III
A
Continuous
Returning the crown to position I
Termination of the chronograph hands
adjustment (can be carried out at any time.
display changes from reference to alarm
III
Turn the crown until the correct date
appears.
* Continue to turn the crown until the
I
II
III
current time 10:39 PM appears.
Push the crown back into position I
(the display changes from reference to
alarm time.)
Please note:
Resetting the time also requires the identical
I
II
III
correction of the reference time.
Please refer to «setting the reference time».
* Please observe the AM / PM clock rhythm.
Switching the alarm on / off
The alarm is switched on / off by briefly
pressing the push-button:
2 beeps alarm switched on
I
1 beep alarm switched off
Please note:
The alarm can be set maximum 12 hours
before the desired alarm time.
Once the set alarm time has been reached,
a signal is emitted for 20 seconds.
This signal is repeated after two minutes.
Following brief pressing of the push-button,
the signal is immediately switched off.
* Push the crown back into position I
(the display changes from reference time
to alarm time).
A signal indicates that the alarm is
switched off.
I
II
III
What is the reference time?
The current time is displayed by means of
the hour and minute hand.
Parallel to the current time, the reference
time runs in the background: the alarm time
refers itself to this reference time. Thus,
must be pulled
resetting the time also requires the identical
correction of the reference time.
If the reference time is not synchronised
must be pushed
with the current time, this results in the alarm
signal being emitted at a different
time to the set alarm time.
, further intervals or inter-
1 x short
long
III
III
III
1 x short
long
III
III
The
time.)
04
Advertisement
Need help?
Do you have a question about the 5130.D and is the answer not in the manual?
Questions and answers