FANATEC CSL Elite Racing Wheel Quick Manual page 2

ATTACHING THE RIM
1
Turn out the fixing screw (J) and open
Use fixation screw (J) and Allen key (I)
clamp ring mechanism.
from box contents.
Use only the Allen Key (I) which comes
with the CSL Elite Racing Wheel!
2
Align CSL Elite Wheel Base (A) axle
to correct position.
Slide CSL Steering Wheel (H) off
3
CSL Elite Wheel Base (A) axle.
Slide CSL Elite Steering
Wheel (H) onto CSL Elite
Wheel Base (A) axle.
Store fixation screw (J) and Allen key (I) safely
for later use.
4
Turn the CSL Elite Steering Wheel (H) top side down to see
EXCHANGEABLE BUTTON CAPS
the bottom side of the clamp ring to follow next step below
5
To detach the button caps, simply pull them out by hand.
They can be replaced with the included set of racing style
Push CSL Elite Steering Wheel (H)
until the screw hole matches with button caps for CSL Elite Steering Wheel (K).
hole on CSL Elite Wheel Base (A) axle
6
Turn in fixation screw (J) to fix clamp
ring mechanism.
Use only the included Allen key (I).
IMPORTANT: Tighten only by using the
short lever of Allen key!
DETACHING THE RIM
1
Insert the table clamp screw with handles (C) into the table
clamp (B).
2
3
Turn the table clamp screw (C) into the bottom centre of the
CSL Elite Wheel Base (A).
TABLE CLAMP
1 3
Slide the CSL Elite Wheel Base (A) onto the table top until
the limiter blocks stop sliding at the edge of the table.
NOTE: Table clamp (B) has to be below table top.
2 4
Tighten the table clamp (B) by turning the table clamp screw
(C). Ensure that the table clamp's feet remain well aligned
with the bottom of the table plate.
CENTRE CALIBRATION
If a centre calibration is needed (e. g. after firmware update of To enter tuning menu press button
wheel base) you need to enter the tuning menu by pressing the menu, use the directional stick:
• Press directional stick up or down to access 5 setups
button as shown on the graphic "S_..." will appear on
• Press directional stick right or left to go through the op-
the display. Now turn the wheel to its centre position and
tions and press or hold it up or down to change option
press two buttons + at the same time to calibrate the
values
wheel centre.
2
S_...
1
Press tuning button
1
2 Turn the steering wheel to the
centre position
Press the two buttons +
3
3
at the same time
SHIFTER CALIBRATION
The CSL Elite Racing Wheel will start in "PlayStation
by default when the CSL Elite Racing Wheel (H) is attached to
the CSL Elite Wheel Base (A). To switch to other modes press
To enter shifter calibration mode, simultaneously press the
the 'Mode' button once. The LED above the " " button will
two buttons + , highlighted below.
indicate the current operation mode:
For the detailed process read shifter manual.
Blue indicates "PlayStation
Red indicates "PC mode"*
Purple indicates "ClubSport Wheel
Base V2 Compatibility Mode"
* PC compatibility not tested nor endorsed by
Sony Interactive Entertainment Europe.
Manufactured by
Fanatec ® is a registered trademark of Endor AG
Designed and developed by Endor AG in Germany
Seligenthaler Straße 16 a - 84034 Landshut - Germany
Telephone: +49 (871) 9221-122 Fax: +49 (871) 9221-221
Email: info.webshop@fanatec.com
Website: www.fanatec.com - www.endor.ag
Licensed for sale in Europe and Australia and for use exclusively with PlayStation
TUNING OPTIONS
. To navigate inside
MODES
4 Mode"
®
4 mode"
®
LED
Mode
4.
®