Champion Power Equipment 100443 Operator's Manual
  1. Manuals
  2. Brands
  3. Champion Power Equipment Manuals
  4. Blower
  5. 100443
  6. Operator's manual

Champion Power Equipment 100443 Operator's Manual

Backpack blower
Hide thumbs
Table of Contents

Advertisement

Quick Links

To reduce the risk of injury, the user must read and understand the operator's manual before using this product. If you do not
understand the warnings and instructions in the operator's manual, do not use this product.
Do not use E15 or E85 fuel (or fuel containing greater than 10% ethanol) in this product. It is a violation of federal law and will
damage the unit and void your warranty. FUEL MIXTURE for this product is powered by a 2-cycle engine and requires pre-mixing
gasoline and 2-cycle oil in a 50:1 ratio. Pre-mix unleaded gasoline and 2-cycle engine oil in a clean container approved for
gasoline. DO NOT mix quantities larger than usable in a 30-day period.
SAVE THESE INSTRUCTIONS. This manual contains important safety precautions which should be read and understood before operating the product. Failure
to do so could result in serious injury. This manual should remain with the product.
Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice.
Made in China - REV 20180905
REGISTER YOUR PRODUCT ONLINE
at championpowerequipment.com
OPERATOR'S MANUAL
or visit championpowerequipment.com
WARNING
NOTICE
Champion Power Equipment, Inc., Santa Fe Springs, CA USA
MODEL #100443
BACKPACK BLOWER

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 100443 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Champion Power Equipment 100443

Summary of Contents for Champion Power Equipment 100443

  • Page 1 This manual should remain with the product. Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice. Made in China - REV 20180905 Champion Power Equipment, Inc., Santa Fe Springs, CA USA...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS 100443 - BACKPACK BLOWER TABLE OF CONTENTS Specifications ..........

  • Page 3: Introduction

    INTRODUCTION 100443 - BACKPACK BLOWER INTRODUCTION SAFETY DEFINITIONS Congratulations on your purchase of a Champion Power The purpose of safety symbols is to attract your attention to Equipment (CPE) product. CPE designs, builds, and supports possible dangers. The safety symbols, and their explanations, all of our products to strict specifications and guidelines.

  • Page 4: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS 100443 - BACKPACK BLOWER IMPORTANT SAFETY INSTRUCTIONS – Before cleaning, repairing, or inspecting, shut off the engine and make certain all moving parts have stopped. Disconnect – Do not allow children or untrained individuals to use this the spark plug wire and keep the wire away from the plug to unit.

  • Page 5: Fuel Safety

    IMPORTANT SAFETY INSTRUCTIONS 100443 - BACKPACK BLOWER Fuel Safety – Fuel is highly flammable. Take precautions when using to reduce the chance of serious personal injury. – Store fuel in a cool, well-ventilated area, safely away from spark and/or flame-producing equipment.

  • Page 6: Safety Labels

    Artwork Notes Revision Changes 2mm safe margin; to be printed on white substrate This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for 1520-L-SF Colors outside parties without the explicit consent of Champion Power Equipment.

  • Page 7: Safety Symbols

    IMPORTANT SAFETY INSTRUCTIONS 100443 - BACKPACK BLOWER Safety Symbols Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to more safely operate the product.

  • Page 8: Operation Symbols

    2mm safe margin; to be printed on white substrate 3. Primer bulb: This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for outside parties without the explicit consent of Champion Power Equipment.

  • Page 9: Controls And Features

    CONTROLS AND FEATURES 100443 - BACKPACK BLOWER CONTROLS AND FEATURES Read this operator’s manual before operating your backpack blower. Familiarize yourself with the location and function of the controls and features. Save this manual for future reference. Backpack Blower 1. Lower blower tube 10.
  • Page 10 CONTROLS AND FEATURES 100443 - BACKPACK BLOWER Parts Included Blower tubes ................. 3 Accessories Spark plug wrench ..............1 Reversible flathead and cross-head screwdriver ....1 Upper Middle Lower Assembly Parts Blower body ................1 Clamps .................. 2 Flex tube ................1...

  • Page 11: Assembly

    ASSEMBLY 100443 - BACKPACK BLOWER ASSEMBLY 3. Loosen wing nut completely on throttle handle clamp. Align notches in throttle handle clamp with guide on the upper Your blower requires some assembly. If you have any blower tube and slide on as shown. When the throttle...

  • Page 12: Operation

    ASSEMBLY 100443 - BACKPACK BLOWER Filling the Tank 5. Assemble middle blower tube to lower blower tube by aligning the arrow of the peg of tube with the arrow of – Place the blower on a flat stable surface, with the fuel tank the locking groove of tube.

  • Page 13: Staring And Stopping

    ASSEMBLY 100443 - BACKPACK BLOWER Starting and Stopping 4. Engage the throttle trigger and safety lock while pushing the throttle lock inwards. NOTICE To avoid breaking the starter rope, do not pull the whole length or let it slide along the edge of the rope guide. Allow the starter rope to rewind gradually.

  • Page 14: To Stop The Engine

    ASSEMBLY 100443 - BACKPACK BLOWER To Stop the Engine: NOTICE To stop the engine, depress and hold the throttle switch to the Allow engine to warm at least 5-10 mins depending on STOP position. ambient temperature. The colder the temperature, the longer the warm up required.

  • Page 15: Throttle Lock

    MAINTENANCE 100443 - BACKPACK BLOWER – To release, squeeze the throttle trigger and safety lock. WARNING Never run the unit without the blower tubes installed. Use of an improperly assembled unit could result in serious personal injury. WARNING Always hold the blower away from your body with the handle in your right hand when operating as a blower, keeping clearance between your body and the product.

  • Page 16: Cleaning The Air Filter

    MAINTENANCE 100443 - BACKPACK BLOWER Cleaning the Air Filter Spark Plug For proper performance and long life, keep the air filter clean. 1. Remove spark plug and check for worn and rounded center electrode. 1. Move choke knob to CHOKE position (See Cold Start section of manual) to prevent dirt and debris from entering 2.

  • Page 17: Storing The Blower

    SPECIFICATIONS 100443 - BACKPACK BLOWER Storing The Blower – Clean all foreign material from the product. Store idle unit indoors in a dry, well-ventilated area that is inaccessible to children. Keep away from corrosive agents such as garden chemicals and deicing salts.

  • Page 18: Parts Diagram (A)

    SPECIFICATIONS 100443 - BACKPACK BLOWER Parts Diagram (A)

  • Page 19: Parts List (A)

    SPECIFICATIONS 100443 - BACKPACK BLOWER Parts List (A) Part Number Description Qty. Part Number Description Qty. Left Band Assembly 24 EB-650.8 Rubber Pillar QS15Q63BF.2 25 EB-650.9 Safty Belt EB-520-E.5 Right Band Assembly GB70.1-GB93-GB97 Bolt Assembly EB-650-10 Clip, Band M6 x 35 M6 ×...

  • Page 20: Parts Diagram (B)

    SPECIFICATIONS 100443 - BACKPACK BLOWER Parts Diagram (B)

  • Page 21: Parts List (B)

    SPECIFICATIONS 100443 - BACKPACK BLOWER Parts List (B) Part Number Description Qty. Part Number Description Qty. EB-650-1 Intake Pipe 1E48FP-E-GJ.1 Muffler 20 1E48FP-E-GJ.2 Heat Shield JB8870 Ø46 - Ø70 Clamp Ø46 - Ø70 Bolt Assembly GB70-GB93-GB97 M5 Bolt Assembly 21 GB70-GB97 M6 x 70 M6 ×...

  • Page 22: Parts Diagram (C)

    SPECIFICATIONS 100443 - BACKPACK BLOWER Parts Diagram (C)

  • Page 23: Parts List (C)

    SPECIFICATIONS 100443 - BACKPACK BLOWER Parts List (C) Part Number Description Qty. Screw ST4.8 × 25 GB845 ST4.8 x 25 Second Half Volute EB-650.2.3 Case EB-650.2.1 Impeller EB-650.7-1 Pan Joint QS15Q63BF.1.1 First Half Volute Case GB97 Ø5 Flat Washer Ø5 GB818 M5 x 55 Bolt M5 ×...

  • Page 24: Parts Diagram (D)

    SPECIFICATIONS 100443 - BACKPACK BLOWER Parts Diagram (D)

  • Page 25: Parts List (D)

    SPECIFICATIONS 100443 - BACKPACK BLOWER Parts List (D) Part Number Description Qty. Screw ST2.9 × 13 GB846 ST2.9 x 13 BL750.3-9 Push Button BL750.3-7 Spring, Push Button CG330B-3E.2.1.2 Left Handle Housing BL750.3-8 Pin, Trigger BL750.3-2 Spring, Trigger BL750.3-3 Self-Lock Trigger BL750.3-4...

  • Page 26: Parts Diagram (E)

    SPECIFICATIONS 100443 - BACKPACK BLOWER Parts Diagram (E)

  • Page 27: Parts List (E)

    SPECIFICATIONS 100443 - BACKPACK BLOWER Parts List (E) Part Number Description Qty. Part Number Description Qty. 1E34F-2E-EMC.1-1 Cap, Spark Plug 1E36F-2C.6.1B Ignition Wire 1E46FP.1-3 Grommet 1E40F-3A.8-2 Spring, Spark Plug Cap GB70-GB93-GB97 M5 Bolt Assembly BPMR7A Spark Plug, BPMR7A x 20 M5 ×...

  • Page 28: Troubleshooting

    TROUBLESHOOTING 100443 - BACKPACK BLOWER TROUBLESHOOTING Problem Cause Solution Fuel mixture is too rich. Open choke. Fuel strainer clogged. Clean fuel strainer. Fuel line clogged. Clean fuel line. Engine does not start. Let unit sit for 15 minutes or remove spark Flooded engine.
  • Page 29 Please register within ten (10) days Limits of Implied Warranty and Consequential Damage from date of purchase. Champion Power Equipment disclaims any obligation to cover any loss of time, use of this product, freight, or any incidental Repair/Replacement Warranty or consequential claim by anyone from using this product.
  • Page 30 United States Environment Protection Agency (U.S. EPA) Emission Control System Warranty Your Champion Power Equipment (CPE) engine complies with U.S. EPA emission regulations. YOUR WARRANTY RIGHTS AND OBLIGATIONS: The US EPA AND CPE are pleased to explain the Federal Emission Control Systems Warranty on your 2018 small off-road engine (SORE) and engine powered equipment.
  • Page 31 EMISSION CONTROL SYSTEM WARRANTY The following are specific provisions relative to your Emission Control System (ECS) Warranty Coverage. 1. APPLICABILITY: This warranty shall apply to 1997 and later model year small off-road engines (SORE). The ECS Warranty Period shall begin on the date the new engine or equipment is delivered to its original, end-use purchaser, and shall continue for 24 consecutive months thereafter.
  • Page 32 You must take your CPE engine or the product on which it is installed, along with your warranty registration card or other proof of original purchase date, at your expense, to any Champion Power Equipment dealer who is authorized by Champion Power Equipment, Inc. to sell and service that CPE product during his normal business hours.

Table of Contents