Table of Contents
Advertisement
Intensive setting
Activate intensive mode to eliminate strong smells and odours.
In this mode, the extractor hood operates at its maximum fan
setting for a short time. After a short time, it automatically
switches back to a low setting.
Switching on
Press the
button on the remote control or the
=
intensive mode on the extractor hood's control panel.
Intensive mode
The
and the first three
#
û
hood's control panel. The fourth
mode is now activated.
Note: After 6 minutes, the extractor hood automatically
switches back to the fan setting that was set beforehand.
Switching off
Press the
button on the remote control or the
=
intensive mode on the extractor hood's control panel.
Intermittent mode
The intermittent function automatically switches on the extractor
hood for 10 minutes every hour. After 24 hours, this function
switches itself off again.
Note: If intensive mode or the run-on function has been
activated, the intermittent function will not be available.
Switching on
Press and hold the
K
button on the remote control or press the
button on the extractor hood's control panel.
Þ
Intermittent function
The
button on the extractor hood's control panel will light up.
#
The first
button and the
û
Þ
the extractor hood's control panel will flash. The intermittent
function is now on. The extractor hood starts at power setting 1.
Switching off
Press the
"
button on the remote control or the
left of the
button on the extractor hood's control panel.
=
This switches off the intermittent function.
6
button for
û
buttons will light up on the extractor
û
button will flash. Intensive
button for
û
button to the left of the
button on
=
Þ
button to the
THE EASIEST WAY TO SELF-IMPORT APPLIANCES DIRECT FROM EUROPE.
Run-on function
The run-on function allows the extractor hood to continue
running for a few minutes after it has been switched off. This
eliminates any remaining cooking smells. The extractor hood
will then switch itself off automatically.
Switching on
Note: If intensive mode or the intermittent function has been
activated, the run-on function will not be available.
Select the power setting.
1.
Press the
K
button on the remote control or the
2.
the run-on function on the extractor hood's control panel.
The
button on the extractor hood's control panel will light
#
up. The first button
and the buttons for the power settings
Þ
that have been applied will flash. The fan continues to run at
this power setting for 15 minutes and then switches off
automatically once this time has elapsed. If the lighting has
been switched on, this is also switched off once the run-on
time has elapsed.
Switching off
Press the
"
or
K
button on the remote control or the
on the extractor hood's control panel.
The run-on function is switched off.
Lighting
The lighting will work even if the extractor hood is switched off.
Switching on
Press the
button on the remote control or the
k
the extractor hood's control panel.
Reducing the brightness
Press and hold the
button on the remote control or the
k
=
button on the extractor hood's control panel until the
brightness has been reduced.
Switching off
Press the
k
button on the remote control or the
the extractor hood's control panel.
Cleaning protection
The appliance is equipped with a cleaning protection function.
When this function is activated, the control panel can be
cleaned without changing the settings.
Switching on
Switch off the extractor hood and lighting.
1.
Press and hold the
button on the extractor hood's control
#
2.
panel for approximately 5 seconds.
Each of the buttons on the control panel will flash, one after the
other.Cleaning protection is now on.
Switching off
Press and hold the
button on the extractor hood's control
#
panel for approximately 5 seconds until the buttons on the
control panel stop flashing.
Cleaning protection is now off.
Þ
button for
#
button
button on
=
=
button on
Advertisement
Table of Contents
