Related Manuals for CUE irCUE
Summary of Contents for CUE irCUE
- Page 1 User Manual irCUE Version 02 CUE, a.s., K Nouzovu 6, 143 00 Praha 4, Czech Republic phone: +420 241 091 240 fax: +420 241 432 446 www.cuesystem.com mail: info@cuesystem.com...
- Page 2 User Manual irCUE UM035_02, 02.04.2009 Copyright © CUE, a.s., Praha, Czech Republic 1990 - 2009. All rights reserved. Specifications are subject to change without prior notice.
-
Page 3: Table Of Contents
Receiver 485........................11 7.1. Mounting .........................11 7.2. Connecting ........................12 7.3. Addressing ........................13 Troubleshooting ........................15 Specifications and Mechanical Drawings................16 9.1. irCUE ..........................16 9.2. irCUE Receiver 485 ......................17 10. Software and Firmware License .....................18 User Manual irCUE www.cuesystem.com Page 3 of 20... -
Page 4: Introduction
/ wood and stainless steel enclosure. Supplied in three versions of wood – mahogany, white birch and oak and two versions of plastic, the irCUE is designed to blend even with the most critical environments. Providing 33 dedicated buttons, the irCUE remote control is prepared to fit perfectly in your hand. -
Page 5: Using
2. Using The irCUE is connected to the rest of control system via IR communication. As IR receiver you can use IR receiver built-in controllers (ipCUE-alpha, beta, delta, epsilon) or external unit irCUE Receiver 485 or receivers built-in keypadCUE-8-L, keypadCUE-8-E. -
Page 6: Charging
It is recommended to connect the irCUE to the docking station at the end of every day. Place irCUE to the docking station also in case there is a lower range of the transmission or when the backlight brightness is reduced. -
Page 7: The Front Panel
Fn button and Fn Indicator Charging indicator The Programmable buttons send IR codes to irCUE Receiver. The Fn button changes first and second function of all programmable buttons. The Fn Indicator lights when the second functions of programmable buttons are selected. -
Page 8: Button Labels
3. Remove the release liner from top part of irCUE. 4. Place the engraved front panel to the upper part of irCUE, Make sure, that the buttons can be pressed easily and then press the panel to stick together with the irCUE. Be as precise as possible, because it very difficult to remove the panel once it has been glued. -
Page 9: Addressing
PLAY button will generate BUTTON_ID: 1026. If Fn is activated, the pressing of the PLAY button will generate BUTTON_ID: 1058. For addressing with irCUE Receiver 485 see chapter irCUE Receiver 485 / Addressing. The button codes are numbers from 1001 to 1032 and they are shown in the following picture. - Page 10 1 to 47 can be set up by the following procedure: 1. Undo four screws on the rear panel of irCUE and remove the rear cover plate. 2. Press the address button on the PCB. The backlight of irCUE is switched on now and Fn LED is flashing.
-
Page 11: Ircue Receiver 485
7. irCUE Receiver 485 7.1. Mounting The ceiling near the center of the room is the best place to install it. The receiver can be mounted to the double ceiling as described in the picture below. The hole diameter is 60 mm. The minimum vertical space for the receiver is 64 mm. -
Page 12: Connecting
7.2. Connecting Using terminals (Phoenix 4-pin, 5.08 mm), irCUE Receiver 485 can be connected to CUEwire. User Manual irCUE www.cuesystem.com Page 12 of 20... -
Page 13: Addressing
7.3. Addressing It is possible to add an offset to a BUTTON_ID sent by the panel using irCUE Receiver 485. It can be very helpful in multi-room installation - the same panel can be identified in each room. That means one panel can start different actions in different rooms - see example in the picture below. - Page 14 The address of the receiver can be set up by the Address Switch - see picture above. The BUTTON_ID sent by irCUE Receiver 485 to the control unit is a BUTTON_ID sent by IR wireless control panel with an added OFFSET value. Button ID and OFFSET values are calculated according to the formulas below.
-
Page 15: Troubleshooting
Charge the accumulator immediately. 3. The IR operating range is short. Check the accumulators in the panel and recharge them. Change the position of the panel or receiver. User Manual irCUE www.cuesystem.com Page 15 of 20... -
Page 16: Specifications And Mechanical Drawings
Enclosure........... Plastic or wood / stainless steel panel Dimensions irCUE (WxHxD)....56 mm (2.2”) x 236 mm (9.3”) x 25 mm (1.0”) Dimensions irCUE Docking Station ..80 mm (3.1”) x 180 mm (7.1”) x 160 mm (6.3”) Weight of irCUE ......... 0.38 kg / 1 lb Supplied accessories ...... -
Page 17: Ircue Receiver 485
9.2. irCUE Receiver 485............. Receiving........... Horizontal level 0 - 360 degrees Vertical level ........60 degrees System connection......CUEwire (RS-485), screw terminals Power supply ........24 VDC (+/- 20%), 1 W Enclosure........... Metal, plastic cover Dimensions........Diameter 81 mm (3.2”), height 104 mm (4.1”) Weight .......... -
Page 18: Software And Firmware License
REGARDING THE SOFTWARE. License Grant: CUE grants to You, as an individual, a license to install and use one (1) copy of the Software on a single computer at a time; provided, however, that You may make copies of the Software solely for Your development of applications for CUE hardware and demonstration versions of such applications. -
Page 19: User Manual Ircue
Notes User Manual irCUE www.cuesystem.com Page 19 of 20... - Page 20 Notes User Manual irCUE www.cuesystem.com Page 20 of 20...
Need help?
Do you have a question about the irCUE and is the answer not in the manual?
Questions and answers