QOLSYS PA-100 User Manual

IQ Outlet User Guide
IQ Outlet
QZ2130-840
Plug In Switch
(Model: PA-100)
INTRODUCTION
Qolsys' IQ Outlet is a Z-Wave Plus® cer�fied device with S2 security and SmartStart
features. You can now add this device securely and with ease using QR code on the
product with compa�ble gateways suppor�ng S2 and Smart Start. The IQ Outlet is
a member of the Z-Wave family and communicates with other Z-Wave cer�fied
devices in a control network. It can be used to turn On or Off lamps or AC operated
appliances. Each Z-Wave device also serves as a node to repeat the signal in the
network, thus, extending the overall Z-Wave mesh wireless network range.
Different types and brands of Z-Wave devices can be associated with the IQ Outlet
in your system and they will work together to op�mize and expand the coverage of
your Z-Wave network.
FEATURES
•
Works with incandescent, florescent (CFL) or LED ligh�ng and AC operated appliance
•
ON/OFF status and loca�on LED indicator
•
Remotely or manually turns ON or OFF lights
•
Does not block the second AC outlet
•
Z-Wave 500 Series module inside
•
Grounded 3-pin AC power receptacle and plug to enhance safety.
•
Internal rese�able fuse to protect from surge current
• Works with any cer�fied gateway suppor�ng Z-Wave
• Please find the QR code label with DSK on the bo�om of the device
! WARNING !
RISK OF FIRE, ELECTRICAL SHOCK & BURNS
DO NOT USE WITH MEDICAL AND LIFE SUPPORT INSTRUMENT
No user serviceable parts are in this module
To reduce the risk of electric shock, this product has a grounding type plug that has
a third (grounding) pin. This plug will only fit into a grounding type power outlet.
If the plug does not fit into the outlet, contact a qualified electrician to install the
proper outlet. Do not change the plug in any way.
The appliance connected to this Z-Wave module must not exceed 900W
incandescent, 200W CFL/LED, ½ horsepower motor and 15A, 1800W resis�ve load.
SETUP
Step 1 Plug in the AC power plug of the appliance
to the receptacle of the IQ Outlet.
Step 2 Insert the module's 3-pin plug into an AC
outlet in the same room as your gateway.
Step 3 Inclusion/Exclusion: Add or remove the device into your network by a
Z-Wave cer�fied controller. The IQ Outlet supports the latest S2 security and
SmartStart offered by Z-Wave cer�fied controllers. If your controller supports S2 or
SmartStart, please refer to the user guide of the controller for detailed instruc�ons
on adding or removing devices to/from the network. You should be able to add the
IQ Outlet into your network using the unique QR code or the DSK 5 digit pin located
on the product or packaging. In addi�on, the device can be added or removed using
the tradi�onal method for Z-Wave as follows:
1. Place your network controller into inclusion mode by following the controller
manufacturer's instruc�ons.
2. When the controller is ready, single click the bu�on on the front of the IQ Outlet.
The controller should indicate that the new device was added successfully.
3. Once the IQ Outlet has been successfully added to your home network, you can
move it to the preferred loca�on in the home.
If the controller shows it failed, repeat the procedure.
Manual Reset
If Inclusion s�ll fails a�er the 2nd a�empt, you need to first reset the IQ Outlet
before repea�ng the above step. The manual reset method is as follows:
1. Unplug the IQ Outlet from the AC
outlet and also unplug the power plug of
the appliance from the IQ Outlet (if
plugged in).
2. Press and hold the bu�on on the IQ Outlet.
IQ Outlet
Size: 5cm x 10 cm, total: 20cm x 30cm (H)
3. Plug the IQ Outlet back into the AC outlet with the bu�on pressed
This product speaks
with other Z-Wave
cer�fied devices
A�er 3 seconds, release the bu�on. If you see the bu�on blink, that means that the
IQ Outlet has been reset successfully and you may retry Step 3 in Setup to add the
module into your network. Otherwise, please repeat the manual reset procedure.
Note: If the IQ Outlet was previously Added (Included) in your network, rese�ng it locally
does not mean it has been removed from your controller so�ware. If you wish to remove
the IQ Outlet from your controller so�ware you will need to remove (Exclude) the
module from the network by your controller. If the IQ Outlet is removed from the
network suppor�ng S2 security, the only way to add the device back into the network is
using the QR code or the DSK code. Therefore, please store the QR code on the product
as well as copy of the full DSK printed on the package in a safe loca�on.
Use the manual reset procedure only in the event that the network primary
controller is lost or otherwise inoperable.
BASIC OPERATION
The connected ligh�ng devices can be controlled manually with a push bu�on
OR Wirelessly with a remotely
A Z-Wave cer�fied controller is capable of se�ng up Qolsys products in your
desired network. Once the device is added, you may assign it to a group.
Please refer to the instruc�ons manual of your controller for details and
procedures on how these se�ngs can be done.
In the event of a power failure, the Qolsys device will return to the last se�ng
a�er the power is restored.
About the push bu�on:
There is a single bu�on on the IQ Outlet for manual opera�on that:
A) Manually turns the connected ligh�ng ON/OFF by pressing the bu�on. It
func�ons as a toggle switch.
Adds (Includes) or Removes (Excludes) your IQ Outlet to/from your Z-Wave
B)
network. Please refer to the instruc�ons manual of your gateway or
remote controller for detail procedures on how these ac�ons can be done.
This push bu�on is also backlit with an LED indicator that will be On when the
connected appliance is Off, and vice versa. The module may be easily spo�ed
even in a dark environment.
Press here