SENAO SN356 Quick Installation Manual

SN356
Quick Installation Guide
Installation
A. Base Unit
Please set up the base unit according to the following steps.
(1) Install the telescopic antenna of the
base unit and extend it fully and
vertically.
(2) Plug in the SENAO AC (2)
adaptor to DC IN jack.
( 3 )
(3) Plug the AC adaptor into
supporting wall outlet.
(5) A standard telephone
may also be plugged into
TEL jack.
B. Handset
To install battery pack:
1
A. Intercom function
1. Paging the handset from the base unit
1.press
Intercom
To stop paging, press
2.To accept a page, press any key except
the charger if handset is locked.
3.To end the intercom, press
onto the Charger.
B. Making a Telephone number:
1. Press
2. Enter phone number
C. Answering incoming Calls:
(5) (4) (4)
Insert the included On incoming calls, the ringer will ring or vibrate unless the ringer
telephone line into
1. If the handset is on charger cradle, lift the handset to pick up the
the LINE jack and
also the telephone incoming call.
line into a wall jack.
2. If the handset is not on charger cradle, press any key to answer
the incoming call except
3. If you do not take the incoming calls, the display will prompt you
have missed.
Note: While receiving incoming calls, you can mute the ring by
pressing
D D . Disconnecting calls:
You can end a call by pressing
the charger cradle.
E. Redial:
1.You can use the up Arrow
numbers dialed. Select and press
2. Press
G. Intercom:
1. Paging the base from the handset:
Press the
to establish intercom.
When the receiving party's voice is heard at the base, answer throug
the built in microphone.
2. Paging the handset from the base:
Press the
Press any key on the handset except
3. Paging the handset from another handset:
This has to be done throuth the walkie-talkie mode. Please refer
to the section. Walkie-Talkie Between Handsets.
H. Walkie-Talkie between handsets:
1. Press the
establish contact..

Base Operation

key, it Means paging all handsets.
again.
Intercom
or remove from
key or place the handset back

Handset Operation

phone number.
.
.
key.
or by placing the handset onto
( ) key to scroll through the last 10 phone
.
, then press OPTION Left soft key redialing the last call.
key on the handset and then press Base (left soft key)
key to establish the intercom.
to answer page.
key followed by the 2 digit unique handset ID to
2
2. The call in progress will be put on hold.
3. You may press and release the PTT key at any time to establish
contact with a separate handset.
4. You can press the and then * key to communicate to all of
the other handsets.
5. The base unit can join the conversation with the 2 other handsets
by pressing the key. By pressing the key again cancels
the group conference.
6. During the group conference, the multi-Talk indicator on the base
unit will be turned on.
MAIN MENU
1. Keypad Settings 1. Keypad Guard Settings
2. Keypad Volume
2. Call Memory 1. Received Calls
2. Dialed Calls
1. Ring Alert Settings
3. Ring Setting
2. Ring Tone
3. Page Tone
4. Ring Volume
5. Group Ring Setting
1. LCD Contrast Settings
4. Parameter
2. Battery Saving
3. Voice Scramble
4. Flash Time
5. Back Light Settings
6. Restore Factory Settings
7. TonePulse Select Settings
1. Customer Name Edit
5. Phone Setting
2. Base Registration
3. Language Settings
4. Direct Incoming
1. Area Code
6. Caller ID
2. +Country Code
3. Call Waiting
3