Table of Contents
Advertisement
Quick Links
English
Read through the Installation Instructions before you proceed
with the installation.
In particular, you will need to read under the "Safety
Precautions" on page 2.
Panasonic Corporation
1006 Kadoma, Kadoma City, Osaka, Japan
Installation Instructions
Wireless Remote Controller
Model No.
Contents
Safety Precautions ...................................... 2
Part Names ................................................... 3
Supplied accessories .................................. 3
Specifi cations .............................................. 3
Installation Precautions .............................. 4
Installation Location for the Receiver ............... 4
Mounting ...................................................... 4
Installing the Receiver ...................................... 4
Wiring ........................................................... 5
Basic Wiring Diagram ....................................... 5
Wiring for the Receiver ..................................... 5
Settings ........................................................ 6
Setting for receiver ........................................... 6
Setting for Wireless Remote Controller ............ 6
Test Operation .................................................. 8
detected contents ............................................. 9
Panasonic Corporation
http://www.panasonic.com
CZ-RWSU3
CV6233317755
H0916-0
Advertisement
Table of Contents
Related Manuals for Panasonic CZ-RWSU3
Summary of Contents for Panasonic CZ-RWSU3
-
Page 1: Table Of Contents
Installation Instructions Wireless Remote Controller CZ-RWSU3 Model No. English Read through the Installation Instructions before you proceed with the installation. In particular, you will need to read under the “Safety Precautions” on page 2. Contents Safety Precautions ........2 Part Names ........... 3 Supplied accessories ........ -
Page 2: Safety Precautions
Safety Precautions Read before installation WARNING Read the Installation Instructions carefully to install the remote controller correctly and safely. • Turn off the circuit breaker of the units before Be sure to read the Safety Precautions in installation. particular before installation. •... -
Page 3: Part Names
Part Names (1) Light receiving section Receives signals. (2) Indication lamp Indicates operation status. (3) Emergency operation button Starts/Stops emergency operation. Supplied accessories Wireless Remote Remote Control LR03 Size Instructions Quick Screw Clamper Controller Holder Battery Reference M4 × 16 Specifi... -
Page 4: Installation Precautions
Installation Precautions Installation Location for the Receiver The wireless remote controllers use a very weak infrared light for its signal, which can result in the signal not being received because of the following infl uences, so take care in where the unit is installed. •... -
Page 5: Wiring
Wiring Basic Wiring Diagram Installation when setting Main/Sub for the remote controller and the receiver Using 1 indoor unit Using more than 1 indoor unit Installation Receiver (Sub) Wired RC (Main) Receiver (Sub) Wired RC (Main) example RC wiring (fi eld supply) •... -
Page 6: Settings
Settings Setting for receiver All set at OFF Check the settings of the when shipped PCB cover Screw [S003] DIP switch on the from the factory. receiver’s PCB. * Remove the cover from the Receiver PCB receiver when performing Main/Sub selector 1 2 3 the PCB settings. - Page 7 Setting Up Remote Controller Functions The functions of the wireless remote controller can be set on site. (These settings are saved in nonvolatile memory in the remote controller. Therefore, the settings do not revert to the defaults even when its batteries are changed.) <Note>...
-
Page 8: Test Operation
Settings Installing Wireless Remote Controller Installation location for the Wireless Remote Controller If a remote controller is to be operated from a remote control holder that is hung on a wall, turn on the lights in the room as well as any electrical appliances and then check to make sure the air conditioner works with the remote controller in the location where it will be installed. -
Page 9: Self-Diagnostics Table And Detected Contents
Self-diagnostics table and detected contents The “Alarm Display” shown in the table below expresses the alarm contents displayed when the wired remote controller is connected. For how to handle the alarms, see installation instructions of indoor units or technical guide. Detected contents Indication lamp on the receiver Alarm Display... - Page 10 © Panasonic Corporation 2016...