Controls - Behringer NX6000 Quick Start Manual

10 NX6000/NX3000/NX1000/NX4-6000/NX6000D/NX3000D/NX1000D
NX6000/NX3000/NX1000/NX4-6000 Controls
(1) (2) (3)
(5)
(7) (8)
NX3000/NX1000
(14)
(7)
NX6000
(1) (2) (3)
(14)
(7) (8)
NX4-6000
(4) (6) (2)
(13)
(9) (10) (11) (12)
(10) (13)
(8) (9) (11) (12)
(4) (6) (2)
(5)
(10) (13)
(9) (11) (12)
11 Quick Start Guide
Step 2: Controls
(EN)
(1) RACK EARS secure the unit into a rack (8) OUTPUTS connect the amplifi er to the
using four attaching screws and washers speakers using professional speaker cables
(fasteners not included). Requires two with twist-locking plugs.
rack units.
(2) VENTILATION openings allow back-to-front
air circulation to prevent overheating.
(3) SIGNAL, LIMIT and PROTECT LEDs display
the signal level and system status for
each channel. The SIGNAL LEDs light to show
the input signal level. The LIMIT LED lights
when the input signal exceeds an optimum
level and activates the internal limiter.
Reduce the input gain if the red LIMIT
LED lights up continuously. The PROTECT
LED shows when an operation error has
occurred (over current, over temperature,
and so on). When an operation error occurs,
the PROTECT LED will light and the unit will
automatically mute the channel until the
error is no longer detected, after which the
PROTECT LED will switch off and the amp will
(9) PIN OUT MATRIX lists the output pin/channel
behave normally.
confi gurations available in each speaker
(4) POWER LED lights up to indicate the unit is
output jack.
powered on.
(10)
VENTILATION FAN speed adjusts
(5) INPUT CONTROLS adjust the input level.
automatically to ensure trouble-
To increase signal gain, rotate the knobs
free operation.
clockwise; to reduce the gain, rotate the
(11) MODE SWITCH Choose the amplifi er mode by
knobs counter-clockwise.
toggling the sliding MODE SWITCH between
(6) POWER button turns the amplifi er on and off .
the MONO, STEREO, and BRIDGE positions
(NX6000: no BRIDGE mode.)
2
(7) POWER SOURCE jack accepts the included IEC
power cable.
(12) CROSSOVER switch chooses between
three modes: FULLRANGE, LF (low frequency
crossover) and HF (high frequency crossover).
In LF mode, the unit amplifi es only the
low frequencies of the signal. In HF mode,
the unit only amplifi es the high frequencies.
LF and HF modes are typically used in
bi-amping applications.
(13) INPUTS Route line-level input signals into
these combination jacks using XLR,
balanced ¼" TRS, or unbalanced
¼" TS connectors.
XLR Plug
¼" TS Plug
¼" TRS Plug
(14)
BREAKER (automated fuse, NX6000 and
NX4-6000 only). After eliminating the cause of
faulty operation, simply depress the BREAKER
and power up the unit again. The BREAKER
acts in place of common discardable fuses.
BREAKER WARNING: Take the following actions
BEFORE resetting the breaker:
• • Unplug the AC main cable
• • Press the POWER button to the extended
"OFF" position
• • Turn all input gain control elements down
2 2
• • And then, reset the breaker, connect the unit to
the mains, switch ON and slowly increase the gain
to the target volume