Page 1
Website:http://biz.LGservice.com E-mail:http://www.LGEservice.com/techsup.html COLOR MONITOR SERVICE MANUAL CHASSIS NO. : CL-70 MODEL: M3200C (M3200C-SAFC.AL**LF) M3200C (M3200C-BAFC.AL**LF) M3200C (M3200C-BAC.AL**LF) ) **Same model for Service CAUTION BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. Downloaded from www.Manualslib.com manuals search engine...
PRECAUTION WARNING FOR THE SAFETY-RELATED COMPONENT. WARNING BE CAREFUL ELECTRIC SHOCK ! • There are some special components used in LCD monitor that are important for safety. These parts are • If you want to replace with the new backlight (CCFL) or marked on the schematic diagram and the inverter circuit, must disconnect the AC adapter...
Page 4
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this 9. Use with this receiver only the test fixtures specified in service manual and its supplements and addenda, read this service manual. and follow the SAFETY PRECAUTIONS on page 3 of this CAUTION: Do not connect the test fixture ground strap publication.
Page 5
General Soldering Guidelines Replacement 1. Use a grounded-tip, low-wattage soldering iron and 1. Carefully insert the replacement IC in the circuit board. appropriate tip size and shape that will maintain tip 2. Carefully bend each IC lead against the circuit foil pad and solder it.
Page 6
Circuit Board Foil Repair At Other Connections Excessive heat applied to the copper foil of any printed Use the following technique to repair the defective copper circuit board will weaken the adhesive that bonds the foil pattern at connections other than IC Pins. This technique to the circuit board causing the foil to separate from or involves the installation of a jumper wire on the "lift-off"...
TIMING CHART VIDEO SYNC << Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (µs), Vertical etc... (ms) >> 1) PC Mode Total Video Front Sync Back Sync Period Porch Porch MODE Active Duration H / V Frequency Resolution Polarity Clock...
Page 8
2) Component Video Mode(Y/Pb/Pr) Total Video Front Back Sync Sync MODE Period Active Porch Duration Porch H / V Frequency Resolution Polarity Clock ( E ) Time ( A ) ( C ) ( D ) ( F ) H(Pixels) 25.175 31.469 SDTV...
BLOCK DIAGRAM(uPD64011+gm1501H) Logo LED Assy 5P Wafer 15P W afer 10P W afer 9P Wafer Po wer Assy RS232 In/Out Control Assy - 9 - Downloaded from www.Manualslib.com manuals search engine...
DESCRIPTION OF BLOCK DIAGRAM 1. INPUT SELECTION CIRCUIT This IC is converting 16bit interlace input signal in to 1) D-SUB RGB INPUT SELECT : This section is 16bit De-interlace signal and the signal is sent to composed of Signal selector IC(BA7657F_U121) Video Signal Processor IC(gm1501H_U402).Ä...
ADJUSTMENT All adjustment are thoroughly checked and corrected 2. DDC Data Write Procedure-Digital when the monitor leaves the factory, but sometimes 1) Use this procedure only when there is some several minor adjustment may be required. problem on Digital EDID data. Adjustment should be following procedure and after 2) Run alignment program for M3200C on the IBM warming up for a minimum of 30 minutes.
Windows EDID V1.0 User Manual 2. EDID Read & Write 1) Run WinEDID.exe Operating System: MS Windows 98, 2000, XP Port Setup: Windows 98 => Don’t need setup Windows 2000, XP => Need to Port Setup. This program is available to LCD Monitor only. 1.
RS232 Select Normal ■ The OSD is displayed when Audio Key is pressed on Nvram Initial in Service Menu. LG Hotel Mode Set Up Channel Change ■ Purpose Input Mode Change - Function : The setting can be adjusted when the unit is being used in a hotel.
TROUBLESHOOTING GUIDE 1. NO POWER NO POWER (POWER INDICATOR OFF) CHECK J601 VOLTAGE CHECK POWER BOARD (18V, 12V, 5V)? CHECK J603 VOLTAGE CHECK POWER BOARD (12V, 24V) ? CHECK X401 CHECK X401 (14.318MHz) ? CHECK J601 CHECK MICOM(U402) (SUB POWER) ? SUB POWER PORT 1.
Page 15
2. NO RASTER(OSD IS NOT DISPLAYED) NO RASTER (OSD IS NOT DISPLAY) CHECK U402 CHECK THE PERIPHERAL IC OUTPUT WAVE? U402 CHECK CHECK WAFER AND POWER INVERTER VOLTAGE BOARD ( 12V,24V)? CHECK CHECK MODULE INPUT MODULE LINK CABLE WAVE? 1. CHECK INVERTER 2.
Page 16
3. NO RASTER STATE ON VIDEO SIGNAL NO RASTER STATE ON VIDEO SIGNAL REMARK : POWER CHECK POWER CHECK OF CXA2040 (U201) : U204(9V) POWER CHECK OF UPD64012 (U801) : U803(3.3V), U804(1.5V) POWER CHECK OF MST9883C (U303) : U304(3.3V) POWER CHECK OF MDIN150L (U901) : U907(3.3V), U908(2.5V) POWER CHECK OF GM1501H (U402) CHECK THE PERIPHERAL NO RASTER IS COMPONENT1...
Page 17
4. NO RASTER STATE ON RGB SIGNAL NO RASTER STATE ON RGB SIGNAL REMARK : POWER CHECK POWER CHECK OF BA7657F (U121) : 5VP POWER CHECK OF SCHMITT TRIGGER (U123, U124) : 5VP POWER CHECK OF MC14066B (U122) : 5VP POWER CHECK OF GM1501H (U402) INPUT WAFER CHECK (J101) CHECK...
Page 18
5. NO RASTER STATE ON DVI SIGNAL NO RASTER STATE ON DVI SIGNAL REMARK : POWER CHECK POWER CHECK OF GM1501H (U402) INPUT WAFER CHECK (J102) NO PROBLEM CHECK THE PERIPHERAL CHECK NO IN / OUTPUT SIGNAL gm1501H(U402) gm1501H(U402) I/O AND SDRAM(U401) SIGNAL? NO PROBLEM...
Page 19
6. SOUND TROUBLE SHOOTING REMARK : POWER CHECK POWER CHECK OF MSP3420G (U501) : U522(8V), L502(8V), L501(5V), L505(5V) POWER CHECK OF TPA3004 (U502) : 18V CHECK SOUND OF VCR,DVD,PC,SETOP BOX... CHECK SOUND INPUT = PC (J707) CHECK NO IN / OUTPUT SIGNAL = DTV / DVD (J702) gMSP3420G(U501) I/O = VIDEO (SVBS, S-VIDEO) (J701)
REPLACEMENT PARTS LIST CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS, READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL. * NOTE SAFETY Mark AL ALTERNATIVE PARTS DATE: 2005. 05. 24. DATE: 2005. 05. 24. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC.