UPM WS928 Owner's Manual

OWNERS MANUAL
1
WS928+WT440H
Wireless Weather Station
Inside temperature /
humidity trend symbol
Moon phase
Comfort level icon
Inside temperature /
humidity reading
Weather forecast
symbols
Month/Day, Year
Outside temperature
reading
Alarm clock
Outside temperature
trend symbol
Clock
Outside humidity reading
Weekday
Outside humidity trend
Pressure reading
Temperature/
pressure historical
Pressure trend symbol
bar graph
WS928 receiver
P.1
MANUAL CLOCK SETTING
Clock 1 Setting
i Press and hold MODE for 3 seconds to enter the clock setting mode
(the CLOCK 1 symbol appears and the time will flash)
ii
Press HOUR to set the hour and MINUTE to set the minute;
iii Press ON/OFF(C/F) during clock setting, to change between
12 and 24 hour display.
i v
iv Do not press any key for 1 minute to finish clock setting
vi
ii
Clock 2 Setting
iii
v Scroll to Clock 2 mode using MODE
vi Press + or - key to change the time
MONTH & DATE, YEAR SETTING
a
Press and hold MODE for 3 seconds to Clock Setting mode
b Press MODE again to Month/Date setting mode
c Press HOUR/+/MAX to set month
a b f
Press MINUTE/-/MIN to set date
d
c f
* The colon symbol " " appears if
d e
date value is 2-digit (e.g. 13, 26...)
e
Press MODE to enter Year setting
f Press HOUR/+/MAX or MINUTE/-/MIN to adjust Year
Weekday is automatically determined from the year/month/day setting
#
*
P.5
KNOW YOUR PRODUCT
WT440H
Snooze/Mode: scrolls through Clock 1 & 2, Alarm 1 & 2,
1
Transmitter
Date & Year, and Temperature Alarm(high & low) mode;
snooze for alarm
2 Ho ur/+/ Ma x: shows ma ximu m temp erature; adjusts
clock, alarm, date & year and temp erature alarm values
Minute/-/Min: shows mi nimum temperature; adjusts
3
clock, alarm, date & year and temperature alarm values
ON /OF F /(C/ F): toggles betwe en C and F, 12 and 24 hour
4
forma t, Alarm 1 & 2 on and off; disables (resets) high &
low temp erature alarms
Ch annel: scrolls through remo te channels Ou tside,
5
Ou tside 2 and Ou tside 3); scrolls through local and remo te
channels (Ou tside, Ou tside 2 and Ou tside 3) in (high & low)
temp erature alarm mo de; activate learn process
6
LCD display
7
SET: enter to House code and Channel setting mode
C/F: change between °C or °F,
8
change channel and house code
9
Battery compartment
10
LCD display
11
11 Wall mount holder &
table stand
P.2
ALARM SETTING
Alarm 1and Alarm 2 setting
1 Scroll to Alarm1 mode (Alarm2 mode) using MODE
2
Press HOUR to set hour
3
Press MINUTE to set minute
4
Press ON/OFF/(C/F) to set alarm on or off
5 When the alarm is set ON, the bell
b 1
symbol / will appear
2
3
4
When alarm sounds
a
or will flash, and the sound volume
will gradually from low to high
#
b
Press SNOOZE to snooze the alarm for 5 minutes,
after that the alarm will sound again
c
Press ANY other key will shut off the alarm.
Without interruption, the alarm will shut off
automatically after one minute
P.6
READ THIS BEFORE YOU BEGIN
button placement
For the best operation,
1 Insert batteries into the remote transmitter(s) first, and then the receiver.
1
Place the receiver and remote transmitter(s) close together. This will ensure that the receiver
2
synchronizes with remote transmitter(s).
2
3 Place the remote transmitter(s) outdoors within an effective transmission range.
3
Although remote transmitters are weather resistant, it is recommended to place it away from direct
*
sunlight, rain or snow. This will help to make condition readings more accurate.
4
# The transmission range can be affected by the dense walls or electronic interference
in between the receiver and transmitter. Try various set-ups for best results.
5
11
GETTING STARTED
STEP 1 : setting the remote transmitters
6
1
Remove battery cover and insert 2 AA size batteries to start setup.
2 The HOUSE CODE will flash for 8 seconds
3 Select the HOUSE CODE by pressing C/F
The range of House Codes are from "01" to "15". Make sure all transmitters
4
in your system are set to the same House Code.
8
10
5 Select CHANNEL(1-4) by pressing C/F. This number will be confirmed upon pressing
7
the SET button, or if no key is pressed for 10 seconds. If only one transmitter is available,
it is recommended to leave the CHANNEL be "01"
6 Humidity & Temperature will display
1
Select °C or °F of Temperature by pressing C/F and pressing SET. Once setup of remote
SET C/F 7
transmitter is completed, it will start transmitting at one minute intervals
* Use a different house code if your weather station detects
other signals from neighboring sources
* Factory default: house code = 01 and channel = 01
STEP 2 : setting the receiver
Remove battery cover and insert 2 AA size batteries. Insert
8
9 9
between terminals observing proper polarity then replace cover.
MOON PHASE
The moon phase is automatically updated
according to the year/month/day.
Moon Phase Display
1
New Moon
2
Young Crescent
3
First Quarter
4
Waxing Gibbous
5
Full Moon
4
6
Waning Gibbous
7
Last Quarter
8
Old Crescent
SYNCHRONIZATION
Automatic Learn Function:
1 The Learn function begins automatically and runs for
3 minutes when receiver batteries are first installed.
2 Within these 3 minutes, the receiver will beep and display
the temperature & humidity signals from transmitter(s).
* If the signals are not received within this 3 minutes, the outside temperature and
humidity will show "
try a different location. Then restart the auto learning function by temporarily
removing the batteries from receiver.
3 5 7
SET C/F
Manual-Learn Function (Searching for Remote Signals):
1
If a new transmitter is added or if signal is lost (outdoor display blinking),
2
1
the learn function must be executed again.
1
4
1
Press and hold Channel for 3 seconds in clock display mode
6 1 %
2
A beep sound indicates that learn function has started
1
3 The Outside symbol will flash and
will beep as each remote sensor is detected
4 Temperature & humidity readings of the
remote sensor will display on the receiver.
8
P.3
TEMPERATURE / PRESSURE
HISTORICAL BAR GRAPH
The bar graph lets you see the pressure trend over a period of 24 hours.
(automatically resets at midnight). The bar graph will show the Pressure
Trend (Default), or the Local or Remote
Temperature by pressing ON/OFF(C/F)
in Clock1 mode.
The sequence is:
Pressure Trend
Inside Temperature Trend
Outside Temperature Trend
( ,
Note: If you have multiple transmitters
press CHANNEL to scroll through below
sequence:
Channel 1
Channel 2
Channel 3
P.7
1 OUT
SET C/F
". If this is the case, bring the units closer togther or
2
the unit
3
1
4
1 OUT
P.4
Pressure Trend
, )
Inside Temperature Trend
Outside Temperature Trend
P.8