Advertisement
Quick Links
CAP7250AG/CAP7252AG/CAP7253AG
Wireless-AC+ABGN Long Range Ceiling Mount Dual Concurrent AP
Please verify contents of the box before continuing to set up the CAP7250AG/CAP7252AG/CAP7253AG.
CAP7250AG/CAP7252AG/CAP7253AG Access Point
12V/2A 100V~240V Power Adaptor
Mounting Bracket
Wall/Ceiling Mounting Hardware Kit
T-Rail Mounting Hardware Kit
*CAP7250AG is 3x3 concurrent 3x3 MIMO access point
*CAP7252AG is 2x2 MIMO internal ANT access point
*CAP7253AG is 2x2 MIMO external ANT access point
Connecting the CAP7250AG/CAP7252AG/CAP7253AG
1) Ensure that the computer in use has an Ethernet Card (RJ-45 Ethernet Port). For more information,
verify with User Manual.
2) Connect one end of the Category 5e Ethernet cable into RJ-45 port of the
CAP7250AG/CAP7252AG/CAP7253AG and the other end to the RJ-45 port on the computer that
will use the CAP7250AG/CAP7252AG/CAP7253AG. Ensure that the cable is securely connected to
both the CAP7250AG/CAP7252AG/CAP7253AG and the Computer.
3) Connect the Power DC Inlet to the DC-IN port of the CAP7250AG/CAP7252AG/CAP7253AG and
the Power to the electrical out.
Note: CAP7250AG/CAP7252AG/CAP7253AG supports both IEEE 802.3at PoE(Power over Ethernet) and
regular power adapter. You should use either one as the power source. Please do not apply both at the
same time.
Quick Installation Guide
Advertisement
Related Manuals for SENAO CAP7250AG
Summary of Contents for SENAO CAP7250AG
- Page 1 CAP7250AG/CAP7252AG/CAP7253AG. Ensure that the cable is securely connected to both the CAP7250AG/CAP7252AG/CAP7253AG and the Computer. 3) Connect the Power DC Inlet to the DC-IN port of the CAP7250AG/CAP7252AG/CAP7253AG and the Power to the electrical out. Note: CAP7250AG/CAP7252AG/CAP7253AG supports both IEEE 802.3at PoE(Power over Ethernet) and regular power adapter.
- Page 2 4) If your PC is already on a computer network, ensure that you have set it to a Static IP Address on the interface (or Ethernet card that will use the CAP7250AG/CAP7252AG/CAP7253AG) as 192.168.1.21 and the Subnet Mask address as 255.255.255.0. (Select Use the following IP Address radio button).
- Page 3 CAP7250AG/CAP7252AG/CAP7253AG, refer to the CAP7250AG/CAP7252AG/CAP7253AG User Manual. Mounting the CAP7250AG/CAP7252AG/CAP7253AG Using the provided hardware, the CAP7250AG/CAP7252AG/CAP7253AG can be attached to a ceiling or wall. To attach the CAP7250AG/CAP7252AG/CAP7253AG to a ceiling or wall using the mounting bracket: 1) Attach the mounting bracket to the wall or ceiling using the provided wall/ceiling mounting hardware kit.
- Page 4 2) Line up the connected T-rail connectors with an appropriately sized rail and press the unit onto the rail until it snaps into place. Note: To protect your CAP7250AG/CAP7252AG/CAP7253AG, use the Kensington security slot to attach a cable lock (cable lock is not included).
-
Page 5: Important Note
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. - Page 6 Professional installation instruction 1. Installation personal This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. The general user shall not attempt to install or change the setting. 2.