Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Nidec-Shimpo DT-2100
Summary of Contents for Nidec-Shimpo DT-2100
- Page 1 99295A...
-
Page 2: Table Of Contents
Contents 1. Introduction 2. Software Operation Requirements 3. Installation 4. Starting Application 5. Main Screen 5.1 USB Connection Status 6. Continuous Data Import Screen 6.1. Measurement Display 6.2 Measurement Results 6.3 CSV File Operation 7. Graph Screen 7.1. Graph Drawing 8. -
Page 3: Introduction
1. Introduction Thank you for purchasing the Handheld Digital Tachometer "DT-2100" (hereinafter referred to as the DT-2100). This instruction manual summarizes the operation procedure of the DT-2100 specialized software. 2. Software Operation Requirements The software operation requirements for the DT-2100 specialized software is as follows: Software Operation requirements •DOS/V compatible machines... -
Page 4: Installation
3. Installation (1) Application installation Double click setup.bat in the installation media "setup" folder to execute installation. When installation is completed, the following files and folders are created under "C:\DT-2100". (2)File configuration Installation Folder Remark destination C drive C:\DT-2100 DT-2100.exe Execution file DT-2100.ini... - Page 5 (3) USB driver installation When connecting a USB device to the PC where the DT-2100 has been installed, the USB driver is automatically installed. Wait for several minutes until the installation is completed. (4) COM port setting Select "USB Serial Port" created under [Control Panel] - [Device Manager], and start to set the port.
-
Page 6: Starting Application
If the driver is not recognized correctly, perform [Update Driver] according to the following procedure. Starting Application Double click "DT-2100.exe" in the installation folder to start application. (1) COM port selection (2) OK button (1)COM port selection* Select from among COM1 to COM15. -
Page 7: Main Screen
(5) MEM_DATA_TRANSFER button Displays the SET_USER screen. (6) SET_USER button (7) SET_SYSTEM button Displays the SET_SYSTEM screen. (8) SEL_USER button Displays the SEL_USER screen. 5.1 USB Connection Status Check the connection status with the DT-2100 in the status display screen. Connected Disconnected... -
Page 8: Continuous Data Import Screen
6. Continuous Data Import Screen Select the "CONT_DATA_TRANSFER button" in the menu to display the continuous data import screen. (1) Measurement display (2) Statistics Data (11) Block tab (1.a) (5) File Save button (6) Restore button (1.b) (7) Start button / Stop button (12) Measurement data (8) Clear Block button... -
Page 9: Measurement Display
(7) Start button Press the Start button to start importing the data. The Start button then becomes the Stop button. /Stop button Press the Stop button to finish importing the data. The Stop button then becomes the Start button. During data import, buttons other than the Stop and Graph buttons, as well as the selection columns are disabled. -
Page 10: Measurement Results
(3) Measurement unit ●Indicates the unit specified in the SET_USER. ●Indicates "OVER" when the measured value exceeds the measurement range. 6.2 Measurement Results (1) Measurement data Measurement operation - 1 Press the Start button to start importing data. It then becomes the Stop button during measurement. Press the Stop button to finish importing data. - Page 11 Measurement operation - 2 Adds a new block for every data import by pressing the Start button. Measurement data is retained. Adds the block tab for every import. Adds the block tab for every import.
- Page 12 (2) Statistics Data From the measurement data, calculates the maximum value/minimum value/average value/standard deviation (Max./Min./Ave./SD). Indicates and retains the data for every import. Calculate and holds the statistics data for every import. (3)Exporting the measurement data Select the arbitrary measurement data. Click the Data Select button to export the selected data. *Multiple data may be selected when you press and hold the Ctrl key while clicking cells with the mouse button.
-
Page 13: Csv File Operation
(4) Deleting the measurement data Click the Clear Block button to delete the block tab that has been selected. 6.3 CSV File Operation The measurement results can be saved in or read from the arbitrary CSV file. ● Save the measurement results in the CSV file Click the File Save button to display the "Save as"... -
Page 14: Graph Screen
7. Graph Screen Select the "Graph button" in the continuous data import screen to display the graph screen. (1)Limit On button／Limit Off button (2) Statistics Data (3) Block tab (9). (7). (6) Graph (8). (5) Horizontal axis (4) Vertical axis selection column selection column (1)Limit On button ／... -
Page 15: Graph Drawing
(5) Horizontal axis selection Select the maximum value on the horizontal axis. Auto: Automatically adjusts to the time during measurement. column Limit: Applies the Limit setting in the USB main screen. When the Limit is 0, the range setting is same as that for the Auto. 10sec, 100sec, 300sec: Sets to the specified measurement time. - Page 16 (2) Switching the display of the upper/lower limit graph Use the Limit On button/Limit Off button to switch between displaying and hiding of the upper/lower limit graph. UPPER_LIMIT LOWER_LIMIT...
-
Page 17: Continuous Data Import Screen
(3) Restore button Indicates the file selection screen. Creates a new block, and reads the selected memory data into it. Indicates the measurement data every time the memory data is read from the DT-2100. Up (4) Block tab to 1000 blocks. -
Page 18: Each Memory
8.2 Each Memory Displays "No." and the corresponding "measurement value" on the first row of the memory data, and the serial number and memory data below them. Indicates the statistics data corresponding to the memory data on the statistics data column. 8.3 Statistics Memory Indicates "No.", "MAX", "MIN", "AVE", and "SD"on the first row of the memory data, and the serial number and memory data below them. -
Page 19: Set_User Screen
Indicates the factory default values. button (4) WRITE button Saves the user setting in the DT-2100 and returns to the main screen. If the MEMORY_MODE value is different from the current setting value in the DT-2100, the confirmation message (OK/Cancel) is displayed. -
Page 20: Set_System Screen
10. SET_SYSTEM Screen Select "SET_SYSTEM button" in the menu to display the SET_SYSTEM screen. (1) Setting value (2) FACTY_DEFAULT button (3)CANCEL button (4) READ button (5) WRITE button (1) Setting value AUTO_OFF Select from 1min, 10min, or 30min AUTO_ZERO Select from 1sec, 10sec, 30sec, 60sec, or None ―... -
Page 21: Sel_User Screen
(4) READ button Reads the current system setting information from the DT-2100. (5) WRITE button Saves the system setting in the DT-2100 and returns to the main screen. Note: default value indicated in bold letters 11. SEL_USER Screen Select "SEL_USER button" in the menu to display the SEL_USER screen. -
Page 22: Error Message List
Perform reinstallation of this exist in the "lc" folder application. ･Check communication The DT-2100 cannot communicate normally with between the DT-2100 and PC, as well as the power Or the COM port number is supply. ･Check the COM port number incorrect from the Device Manager. - Page 23 In the memory data import Open the measurement data screen (statistics memory saved in the statistics memory mode), tried to open the mode measurement data saved in modes other than the statistics memory mode There is a blank in the input Enter the value in the item.
- Page 24 GRAPH_MIN value is higher than the GRAPH_MIN higher than the GRAPH_MAX value. value Measurement data cannot be Check that the DT-2100 is in imported correctly from the the correct mode for DT-2100 measurement. The Start button was pressed Start measurement.
-
Page 25: Terms Of Use
13. Terms of Use Please read the conditions of use below carefully before using this Special software of Handheld Digital Tachometer DT-2100 (hereinafter referred to as “this software”). By using this software, the user shall be subject to the terms and conditions below. -
Page 26: Communication Commands
14. Communication Commands For communication commands, refer to the "RS232C Command List".