Advertisement
1. Installing the repeater
1. Refer to the previous topic to plan the installation.
2. For all cameras that are in range of the WAP-PLUS and DO NOT need the extended range of the
Repeater, these cameras must be installed first. Refer to the camera's installation guide for directions.
(Note, for existing systems this may have already been done.)
3. For all cameras that are out of range of the WAP-PLUS continue to the next step.
4. Select a power outlet for the WREX that is powered on all the time and not tied to a switch. Further,
an outlet that is higher is preferable.
5. On the Repeater, depress the POWER button and allow time for the POWER indicator to stop blinking
and remain steady (approximately 40 seconds).
6. Apply power to each camera that is to be associated with the Repeater.
7. Configure wireless security for the Repeater as described to the right.
NOTES:
Refer to the installation guides for the WAP-PLUS, ACU (Analog Converter Unit), and each camera for
detailed information about that product.
If using more than one wireless camera, each must be configured for wireless security. Configure one
camera at a time.
When setting up a wireless configuration in very large buildings or buildings with dense walls, wireless
communications may be marginal. It is best to first configure the system in the same room. Then
upon successful configuration, place each camera in the desired location. Verify that all cameras
exhibit good communications as indicated by a STEADY GREEN Power LED and a Network LED that
occasionally BLINKS GREEN.
3. Enroll or edit the camera(s) in AlarmNet Direct
Dealers can enroll the camera and set up a Total Connect account for their customers by
visiting the AlarmNet Direct website:
https://services.alarmnet.com/AlarmNetDirect/
Go to the online help and;
For customers with no AlarmNet accounts – follow the procedure for "
Services Only Account
."
For customers with an existing "Video Only" account – just add the new camera.
For customers with an existing AlarmNet GSM or Internet communicator account –
ensure the account number is green (registered) and the Has Remote Service Capabilities icon is
present. Then just add the new camera.
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the
equipment.
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has
been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in
a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the radio or television receiver away from the receiver/control.
INDUSTRY CANADA CLASS B STATEMENT
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
DECLARACIÓN COFETEL
La operación de este equipo está sujeta a las siguientes dos condiciones.
1. Es posible que este equipo o dispositivo no cause interferencia perjudicial y.
2. Este equipo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.
Ê800-14129:Š
800-14129 7/13 Rev. C
2. Configure wireless security
Linking the Repeater to the WAP-PLUS
1. Ensure the WAP-PLUS is on and fully booted (allow 2 minutes for the boot process to
2. Ensure the Repeater is on and fully booted (approximately 40 seconds).
3. At the WAP-PLUS, press and hold the WPS button for 3 seconds, then RELEASE. Verify
4. At the Repeater, within 1 minute, press and hold the WPS button for 5 seconds, then
5. Verify the repeater's WPS indicator blinks slowly at first then the WAP-PLUS Uplink
Linking the Repeater to its associated cameras
1. Ensure the cameras are powered up and fully booted (allow 2 minutes for the boot
2. At the Repeater, depress the WPS button, then RELEASE.
3. At the camera, within
4. Allow up to 45 seconds for the WPS process to complete. Then at the camera, verify
5. Repeat the above steps for each camera.
NOTES:
If the WREX is power cycled, a camera may need 10-15 minutes to re-establish connec-
If the camera is being used in a wireless mode, and the Reset button was used to
When the Repeater and its associated cameras are set up and the customer's Total
Connect account is established, they can view their video by visiting:
http://www.mytotalconnect.com/
The cameras are now ready for customer use.
Creating a Video
Have the customer log into their Total Connect account to view the video.
If their PC does not have QuickTime® and Flash® player, you will be prompted to install or
update these applications.
If any of the cameras were mounted upside down, there is a setting to upright the image.
At this time the location of each camera can be adjusted for the desired view.
When adding, editing, or deleting a camera, the customer will receive email notification.
For detailed camera operation refer to the Total Connect online help guide.
FEDERAL COMMUNICATIONS COMMISSION STATEMENTS
CLASS B DIGITAL DEVICE STATEMENT
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.
• Consult the dealer or an experienced radio/TV technician for help.
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and RSS210 of Industry Canada. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est
soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit accepter toute
interference reçue y compris les interferences causant une reception indésirable.
Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência
prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter
primário.
Honeywell is a registered trademark of Honeywell International Inc.
Flash is a registered trademark of Adobe Systems Incorporated, registered in the U.S. and other countries.
QuickTime is a registered trademark of Apple Inc., registered in the U.S. and other countries.
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright 2013 Honeywell International Inc.
www.honeywell.com/security
complete).
the WAP-PLUS Security light starts blinking (other wireless access points may be
different).
RELEASE.
signal strength indicator lights steady green. (This process may take 5 minutes so be
patient.) If the WPS indicator switches to a fast blink that indicates a WPS failure.
Repeat the above steps.
process to complete).
1
minute, click and RELEASE the WPS button on the camera.
successful wireless security as indicated by a STEADY GREEN Power LED and a Network
LED that occasionally BLINKS GREEN. If these indicators are present you are done.
tivity to the WREX repeater.
restore factory defaults; you must delete that camera from the AlarmNet Direct account,
and enroll it back into the account. Then reconfigure wireless security for that camera.
DECLARACIÓN ANATEL
TRADEMARKS
WARRANTY
For the latest warranty information go to:
http://www.security.honeywell.com/hsc/resources/wa/
Advertisement
