Intermatic HA18 Installation And Programming Instructions

Federal Communications Commission Statement / Industry Canada Statement
This device complies with part 15 of the FCC rules. Operation of this device is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna or device.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTICE — Changes or modifi cations not expressly approved by Intermatic Inc., could void the user's authority to operate the equipment.
The term "IC" before the radio certifi cation number only signifi es that Industry Canada technical specifi cations were met.
Limited Six-Year Warranty
If within six (6) years from the date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its sole option, free of charge. This war-
ranty is extended to the original household purchaser only and is not transferable. This warranty does not apply to: (a) damage to units caused by accident, dropping or abuse in handling, acts of God or
any negligent use; (b) units which have been subject to unauthorized repair, opened, taken apart or otherwise modifi ed; (c) units not used in accordance with instructions; (d) damages exceeding the cost
of the product; (e) sealed lamps and/or lamp bulbs, LED's and batteries; (f) the fi nish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear; (g) transit
damage, initial installation costs, removal costs, or reinstallation costs.
INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES. ALL IMPLIED WARRAN-
TIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED
WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE
ABOVE LIMITATION MAY NOT APPLY TO YOU.
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing the product, along with proof of purchase, postage prepaid to the
authorized service center listed below. This warranty is made by: Intermatic Incorporated/After Sales Service/7777 Winn Rd., Spring Grove, Illinois 60081-9698/815-675-7000 http://www.homesettings.com
Please be sure to wrap the product securely to avoid shipping damage.
INTERMATIC INCORPORATED
SPRING GROVE, ILLINOIS 60081-9698
• Electrical shock hazard. Risk of injury or death. Remove electrical
power at service panel before installing.
• Follow local electrical codes during installation.
• For indoor use only.
Before installing, make sure that you...
• Understand basic wiring principles and techniques
158HA13316
QUALIFIED ELECTRICIAN FOR THIS INSTALLATION.)
• Can interpret wiring diagrams
• Have circuit-wiring experience
• Read all instructions and documentation and save for future reference
• Are prepared to test your work, making sure you have wired the recep-
tacle according to your local electrical code
Thank you for purchasing an Intermatic HomeSettings device
With HomeSettings devices, you can reliably and remotely
control your lighting and appliances. The outstanding features
of the HomeSettings HA18 15 Amp In-Wall Switch include:
•
Feedback that will allow you to see whether your device has
received the ON/OFF signal.
•
Wireless signal reliability — each HomeSettings product
has a special feature that virtually guarantees that wireless
signals are received.
•
Manual override.
•
Can be used with decorator-style wall plates (not included)
•
Compatible with multiple location
conventional 3-way or 4-way wiring devices.
Because the HA18 In-Wall Switch is a Z-Wave™ device, it is
compatible with any HomeSettings network, other Z-Wave net-
works, and all HomeSettings or other Z-Wave devices display-
ing the Z-Wave logo, regardless of manufacturer.
Each module in a Z-Wave network com-
municates with every other module,
acting as a "repeater" and routing your
commands to their destination by the
most reliable pathway. When Z-Wave
devices (regardless of manufacturer)
are installed throughout the house,
signals are automatically routed around
obstacles or dead spots, strengthening the network as more
devices are added.
MODEL HA18
15 Amp In-Wall Switch
Installation and Programming Instructions
1 – Wire and Install the HA18 In-Wall Switch
The most basic installation procedure is to use the HA18 in a
Single Pole application—a circuit where a single switch controls
a light or outlet, as shown in the wiring diagram below.
Single Pole Application
HOT
WARNING
120VAC
50/60 Hz
NEUTRAL
Other installation diagrams are shown on the next page.
1.
Turn off power at the service panel by REMOVING THE COR-
RECT FUSE or TURNING THE CIRCUIT BREAKER OFF.
2.
Remove existing wall switch from the box if necessary.
(IF NOT, USE A
3.
Trim building wires to 7/16".
4.
Connect the BLACK wire of the HA18 to the hot build-
ing wire (the wire leading to the circuit breaker or
fuse box), using a twist connector (provided).
NOTE: Twist connectors provided are suitable for
copper wire only. For aluminum wire, consult an
electrician.
NOTE: Insert wires straight into twist connector, then
twist clockwise. Make sure all twist connectors are
tight. Secure each twist connector with electrical tape.
Make sure no bare wire shows below the wire con-
nector.
5.
Connect the BLUE wire of the HA18 to the load wire, using a
twist connector (provided).
6.
Connect the WHITE wire of the HA18 to the neutral building
wire, using a twist connector (provided).
7. Connect the ground wire from the box to the bare copper
wire on the HA18 In-Wall Switch. If there is no ground wire,
ground the HA18 unit to the box. If the box is plastic, con-
nect the bare copper wire to ground as supplied or contact
ON/OFF control using
an electrician.
8.
Remove the semi-stripped end of of the RED wire and
apply the twist connector to this wire. The RED wire is not
used in the single-pole application.
9.
Tuck wires into wall box leaving room for the HA18 unit.
10.
Using screws provided, mount the HA18 unit to the wall box,
then install the decorator wall plate (not provided).
11. Turn power back on at the service panel.
• To manually turn ON the light switch, press and release the top rocker.
• To manually turn OFF the light switch, press and release the bottom
rocker.
BLACK BLUE LOAD
BARE
Incandescent
RED
COPPER
Lighting Load
WHITE
HA18