GreenBrook DH020A Manual

Instructions for wired doorchimes & pushes

Advertisement

INSTRUCTIONS FOR WIRED
DOORCHIMES & PUSHES
MODEL NUMBERS -
Doorchimes -
DH020A: Galaxy Chime
DH021A: Tubular Chime
DH022A: Moon Chime
DH050A: Galaxy Chime Kit
Bell Pushes -
If you have bought a bell push only
please go straight to STEP 3a. in these
instructions.
DP010A: Black Bell Push
DP020A: White Bell Push
DP050A: Brass Plate Bell Push
DP060A: Brass Bell (with name card)
DP070A: Brass Surface Mount Bell
DP080A: Brass Bell Push
DP090A: Brass Round Bell Push
DP100A: Antique Copper Bell
DP110A: Wrought Iron Black Bell
DPL12A: 'Push A Lite' Brass Push
DPL13A: 'Push A Lite' Silver Button
(for DPL12A & DPL13A please also
note step 3b)
DPL03A: Lit (illuminated) Black Bell
DPL04A: Lit (illuminated) White Bell
(DPL03A & DPL04A must be used with a
bell transformer)
This doorchime has a traditional
ding-dong sound and is easily
fitted for use with any door push.
• Bell wire required (included
in DH050A Galaxy Chime Kit)
• Bell push required (included
in DH050A Galaxy Chime Kit).
An ornate door push can be
used if preferred. (For lit bell
pushes a transformer must
also be used - GreenBrook
Model Number 'DAT01A')
• Fixing screws included
• Requires 3 x C cell R14
batteries (not included)
PLEASE READ THE FOLLOWING
INSTRUCTIONS FULLY BEFORE
ATTEMPTING INSTALLATION.
STEP 1.
PREPARING BELL WIRE
1) Using a knife, carefully split
the bell wire down the
middle to form two separate
wires, each 30mm long.
2) Strip each wire back to expose
5mm of copper wire.
3) The process will
need to be
repeated at the
other end of
the bell wire once
it has been cut to
the required length.
4) The bell wire is now ready to
wire up the doorchime to the
bell push.
STEP 2. WIRING
YOUR DOORCHIME
1) Unclip top cover.
2) Thread bell wire from the
back of the base and through
the large opening to the left
of the keyhole slot.
3) Insert either one of the
stripped ends to terminal A
and the other to terminal C,
ensuring the terminal screws
are tightened securely after-
wards. Do not use terminals
marked B and D.
4) Position the base on the wall
vertically, away from opening
doors, with the battery
compartment at the bottom.
Ensure that it is less than 5
metres away from the bell
push.
5) Use one of the screws and
wall fixings to hang the base
on the wall via the top key
hole slot. Adjust the screw for
a flush fit if required.
6) Insert 3 x C cell batteries as
per markings on the inside of
the case.
STEP 3a. WIRING
YOUR BELL PUSH
1) If necessary, remove the base
cover of the bell push to
reveal the terminal screws.
2) Loosen one of
the terminal screws
and wrap one of
the stripped ends
of bell wire around
the exposed screw
thread, ensuring

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DH020A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for GreenBrook DH020A

  • Page 1 DH050A Galaxy Chime Kit). An ornate door push can be used if preferred. (For lit bell pushes a transformer must also be used - GreenBrook Model Number ‘DAT01A’) • Fixing screws included • Requires 3 x C cell R14...
  • Page 2 FUTURE REFERENCE Certain door push models can be converted to illuminated pushes by purchasing either a GreenBrook DPL12A or DPL13A If after going through the trouble bell push button separately. Please shooting section, you still note:For illuminated pushes, a bell experience difficulty please ring transformer must be used.

This manual is also suitable for:

Dh021aDh022aDh050a

Table of Contents