VARES Mnichovice a. s. Pražská 539 251 64 Mnichovice info@vares.cz www.vares.cz Tel : 323 631 333, 323 631 334 Fax: 323 640 466 INSTRUCTIONS FOR USE Fruit Crushers DZO 16 N (SHARK FRUIT 1.6)
Table of contents Page Introduction Symbols used in this User’s Guide and on the machine ............... 3 Safety symbols used in the User’s Guide .................. 3 1.1.1 1.1.2. Safety symbols on the machine ....................3 1.1.3. Other symbols used on the machine ..................4 1.1.4 Machine manufacturer plate design 1.1.5...
Introduction This User’s Guide is intended for the users of DZO 16N type fruit crushers manufactured by VARES Mnichovice a.s. The User’s Guide forms an integral part of the technical documentation which the manufacturer and supplier of the equipment makes available to users. The User’s Guide contains all necessary information for an overall familiarisation with the features and functions of the crusher’s individual...
INPUT Product identification Garden refuse crushers type DZO 16 N are designed for crushing fruit for further processing (cider making …). The crushers are by their design and parameters suitable particularly for hobby gardeners. The main advantage of these machines is their adequate performance, compactness, simple operation and ease of moving them.
IP 23 The shown types of garden refuse crushers have the following commercial designation: DZO 16 N – SHARK Fruit 1.6 Other technical data The machine’s electrical equipment is Protection Class I equipment according to ČSN 33 0600 Clause 3.2.
- If the machine is put out of use for whatever the reason, its electrical equipment must be disconnected from power supply and its switched off state secured by pulling the machine’s power cord plug out of the power socket. - Safety markings, symbols and signs on the machine must be kept readable.
- Arm injury of injury of other parts of the body when inserting long foreign objects (other than the material to be crushed) into a running machine. - Leg injury or injury of other parts of the body caused by a tumbling machine while being carelessly moved. 4.4.2 Electrical hazards: Hazards:...
5.2.1 Top part (see Fig. 1) The part is formed by a circular chute, a bull-headed tube and a top part of the crushing mechanism with four holes for fastening screws. The entire top part including the bulkheads is made of food industry stainless steel.
Figure 3 Bottom part Cutting disc Bottom roller, 17 mm, stainless steel Top roller, 17 mm, stainless steel Distancing (limiting) washer M 8x35 stainless steel, propeller head screw M 8x16 screw, stainless steel, with sunken head 8.4 washer, stainless steel Electromotor 10.
WARNING! Due to the fact that crushed material is handled in the vicinity of the crusher, there is an increased danger of slipping and tripping in this area. Connecting the machine to power supply The crusher’s electrical equipment can be connected only to the corresponding single-phase, 230 V, 50 Hz power socket with a protective contact connected to a protection wire.
Shutdown After finishing the work, shut the crusher down as follows: - After finishing the work, let the crusher run until the work mechanism is completely empty, i.e. until no crushed material comes out any more from the discharge gate, then switch the crusher off by turning the switch lever to the position O “OFF”.
Preferably use a new blade. Sharpening reduces the blade’s weight and puts the Note: cutting disc out of balance. Large imbalance will cause vibrations of the whole crusher and excessive stressing of the electromotor bearings. Important! When machine-sharpening the blade, you must simultaneously cool it with water, otherwise the blade edge will loose its hardness and cutting ability! Before fitting the blade to the cutting disc, carefully clean all contact surfaces, both on the blade and the disc.
Packaging, Transportation, Manipulation and Storage 12.1 Packaging The machine is packaged in a carton box. 12.2 Transportation and manipulation IMPORTANT! When handling the machine by a lifting device, abide by safety regulations applicable to such operations! The machine can be manipulated by hand. When manipulating the machine, please take into account its weight, size and centre of gravity.
Page 14
W a r r a n t y C e r t i f i c a t e A Warranty Certificate belongs to the sold product of the corresponding type and serial number as part its accessories. It must be presented every time a claim is made. Provided warranty conditions have been met (Chapter 14 of the User’s Guide), we provide the consumer with a 24-month warranty after the date of sale...
Page 17
Address: IČ: 00662437 Identification Number: Jméno a adresa osoby pověřené VARES Mnichovice a. s., Ondřejovská 699, 25164 Mnichovice, sestavením technické dokumentace: CZECH REPUBLIC Name and address of the person authorised to compile the technical file: Drtič ovoce typ SHARK Fruit / Fruit crusher type SHARK Fruit Výrobek (stroj) - typ:...