Related Manuals for Spectrum MixH2O-PRO
Summary of Contents for Spectrum MixH2O-PRO
-
Page 1: Table Of Contents
Installation, Service & Spectrum Operation Manual MixH O-PRO Water Softener Table of Contents General Notes Description & Equipment Adjustments Components, Features & Functions Component Contents Valve User Interface Installation Instructions Valve Programming Set-up p.10 Troubleshooting p.13 Cautions p.15 Technical Information... -
Page 2: General Notes
This manual is for a range of softeners based on the SPECTRUM 5, 7 and 12 valve going from 25 to 350 litres of resin. Please take a look at the model supplied as this will have an influence on various parameters for starting up your softener, especially on the programming side. -
Page 3: Description & Equipment Adjustments
Spectrum 2. Description & Equipment Adjustments Please use this sheet to keep a record of your system parameters and installation. Installation Number Nominal Capacity °tH Valve Serial Number Inlet Water Hardness °tH Tank Size Treated Water Volume litres Resin Type Outlet Water Hardness °tH... -
Page 4: Components, Features & Functions
SPECTRUM 5 exhausted, the resin bed needs to be regenerated. Before the regeneration of the resin bed, a backwash 7.5V transformed for SPECTRUM 7 and 12 step is necessary for two main purposes; removing the valves residue in the resin bed and loosening the impacted... -
Page 5: Component Contents
4.1. SPECTRUM 5, 7 or 12 Valve 4.2. SPECTRUM Pressure Vessel & Riser Tube 4.3. SPECTRUM Brine Tank 4.4. -
Page 6: Valve User Interface
Spectrum 5. Valve User Interface 5.1. SPECTRUM 5 Valve Flow Rate Indicator Regeneration Indicator Bypass Parameter Display Time Display Cycle Nº Next Button ( Up Button ( Down Button ( Regeneration Button ( Blending Valve Drain Line Brine Line Outlet... - Page 7 Spectrum 5. Valve User Interface 5.2. SPECTRUM 7 & 12 Valve Cycle Nº Flow Rate Indicator Regeneration Indicator Time Display Up Button ( Down Button ( Next Button (...
-
Page 8: Installation Instructions
Spectrum 6. Installation Instructions 6.1. Prerequisites The softener needs to be installed onto the mains water supply. Piping has to comply with the regulations of the country where it is installed. Your softener will require space for maintenance and operation. Please allow enough room on the top to remove the valve should it be needed. - Page 9 Use Teflon® tape if necessary in order to seal between the drain fitting and the outlet flow control. 6.3. Connecting SPECTRUM 5 Valve SPECTRUM 7 & 12 Valves 6.4. Start Up 1. Half fill the brine tank with water. 2. Add salt until in total the brine tank is ¾ full.
-
Page 10: Valve Programming Set-Up
Spectrum 7. Valve Programming Set-Up 7.1. Programming To enter ‘Master Programming Mode’ set the time to 23:45 and press the next ( ) button for 8 seconds. The recommended options for your system have been highlighted below in green. The values to input based on your individual installation have been highlighted In yellow below. - Page 11 Spectrum 7. Valve Programming Set-Up Adjust the value using the up ( ) and down ( ) arrows. This is the volume in cubic meters your system can soften. The capacity can be determined with the ‘Capacity Calculation Table’ overleaf.
- Page 12 Spectrum 7. Valve Programming Set-Up 7.2 Capacity Calculation Table The values in the table below show the volume of soft water produced between regenerations (m³). Volume of Resin (Litres) Hardness Level (ppm CaCO 12.5 25.0 37.5 50.0 75.0 125.0 175.0 10.4...
-
Page 13: Troubleshooting
Spectrum 8. Troubleshooting 8.1. PRO System Problem Possible Cause Possible Solution 1. Power off 1. Switch on power 2. Transformer is not plugged in 2. Connect to constant power source A. Controller does not work 3. Defective power cord 3. Replace cord 4. - Page 14 Spectrum 8. Troubleshooting 8.2. PRO Valve Problem Possible Cause Possible Solution 1. Used or defective batteries 1. Replace old batteries 2. Disrupted electric supply 2. Recover the power supply 3. Damaged meter cable 3. Verify the connection & inspect cable A.
-
Page 15: Cautions
Spectrum 9. Cautions 1. Without reading and understanding the contents of this user manual, DO NOT perform any operations on the control valve. 2. Strictly prohibit a leaning position when shipping, installing and using this product as this could cause damage. -
Page 16: Technical Information
Spectrum 10. Technical Information Model (litres of resin) Maximum Operating Temperature (ºC) Minimum Operating Temperature (ºC) Maximum Operating Pressure (bar) Minimum Operating Pressure (bar) Max Flow Rate (m /hr) Optimal Flow Rate (m /hr) Inlet / Outlet (") ¾ BSP ¾... - Page 17 Spectrum WWW.SPECTRUM-FILTRATION.COM...