LG Electronics. Unauthorized modifications will not only void the warranty, but may lead to property damage or user injury. If wires, screws, clips, straps, nuts, or washers used to complete a ground path are removed for service, they must be returned to their original positions and properly fastened.
LDF9810ST DISHWASHER SAFETY TIPS • Disconnect the power before servicing the dishwasher. • Reconnect all grounding devices after repairs are complete. This includes all grounding wires that are attached by screw and ring connector as well as the power input, whether cordset and outlet or hardwired.
LDF9810ST DISHWASHER SPECIFICATIONS ITEM SPECIFICATION Rated Input 120 V , 60Ø Installation Built-in Capacity 14 place settings Dimensions (inches) 23⅞ X 25 X 33⅞ Weight (pounds) Door Color Black, White, Stainless Stainless Steel Control Electronic Programs 6 Cycles Rated Power (Watts)
Page 9
LDF9810ST DISHWASHER FEATURES, continued 1. Control Panel 2. Door Handle 3. Front Cover 4. Lower Cover 5. Leveling Foot 6. Side Cabinet 7. Base 8. Top Spray Arm 9. Upper Spray Arm 10. Removable Tines 11. Steam Nozzle 12. Lower Spray Arm 13.
LDF9810ST DISHWASHER INSTALLATION Installation is covered briefly for the servicer who may need to uninstall and reinstall the dishwasher for repairs. For new installations, please refer to the installation guide that was supplied with the dishwasher. • We recommend a location as close to the sink as possible (but not directly under it) for easy connection to water and drain lines.
LDF9810ST DISHWASHER ELECTRICAL SUPPLY PREPATATION The dishwasher can be hardwired if necessary and if permitted by local code. We recommend the use of a dishwasher installation kit, available at most hardware and home supply stored. This kit includes a cordset, a flexible water supply line, and the elbow connector necessary to connect it.
LDF9810ST DISHWASHER DRAIN CONNECTION The drain hose must be connected in a manner that meets the local plumbing code. If the end of the drain hose does not fit the available connector, an adapter may be obtained from a local hardware or plumbing supplier.
LDF9810ST DISHWASHER FINAL INSTALLATION 1. Turn on the water at the valve under the sink. 2. Turn on the power at the fuse or breaker (or plug in the cordset at the outlet under the sink. 3. Run the dishwasher through one QUICK cycle to check the operation and to check for water leaks.
LDF9810ST DISHWASHER CONTROL PANEL SOAK Heavily soiled loads, with cooked-on foods POWER SCRUB Normal soil level, everyday loads NORMAL Normal soil level, everyday loads STEAM DELICATE Washing delicate items, crystal, stemware QUICK Light soil level, recently used dishes and cutlery...
LDF9810ST DISHWASHER PROGRAMS DUAL INTENSITY SPRAY WASH The spray intensity for the upper lower racks is programmable by the customer. By selecting SOFT SPRAY for the upper rack and STRONG SPRAY for the lower rack, you can wash delicate items like stemware on top while washing pots and pans on the bottom.
LDF9810ST DISHWASHER ADDING DETERGENT Detergent must be added to the dispenser before the start of every cycle except RINSE ONLY. The detergent chamber holds 1.4 oz. (40 g) when full. If the dishes are only moderately dirty, it might be possible to use less detergent.
LDF9810ST DISHWASHER ADDING RINSE AID Turn the round cap counterclockwise and remove it. Fill the reservoir. It holds 4.8 oz. (145 ml) Replace the cap and lock it. Adjust the rinse-aid setting as necessary. The factory setting for rinse aid dispensing is 3. Too little rinse aid contributes to spotting, streaking, and poor drying performance.
LDF9810ST DISHWASHER ERROR CODE POSSIBLE CAUSE SOLUTION • Inlet water temperature too • Check water temperature hot (over 194° F or 90 °C) using TEST MODE (See Page 13.) • Wiring connection defective If temperature is displayed, adjust water THERMAL •...
LDF9810ST DISHWASHER DISASSEMBLY / REPAIR Before disassembling the dishwasher: • Unplug the dishwasher or turn off the breaker (or fuse) Disconnect the wire if the dishwasher is hard-wired. • Turn of the water supply • Remove all dishes and racks •...
LDF9810ST DISHWASHER DOOR ASSEMBLY FRONT COVER Open the door. Remove 12 screws (stainless steel). CONTROL PANEL ASSEMBLY Remove 2 screws (stainless steel). Remove the wire connections. (Do not reverse at reassembly!) Remove the latch assembly. Remove the front display. Remove 8 screws to take out the controller (main board).
LDF9810ST DISHWASHER DOOR ASSEMBLY, continued FAN ASSEMBLY Remove the front cover. (See page 25.) Remove 4 screws and a ground screw for the door bracket. Remove the wire connections from the fan. Remove the air duct. Unscrew the inner cover to remove the fan assembly.
LDF9810ST DISHWASHER LOWER FRAME Press the holder hooks as shown. Remove the 4 screws. Turn the dishwasher upside down. DRAIN HOSE HOLDER Press the holder hook as shown. Pull the drain hose and remove the drain hose holder. BASE COVER Remove 2 screws.
LDF9810ST DISHWASHER LINE NOISE FILTER Disconnect both connectors of the line noise filter. FLOAT SWITCH ASSEMBLY Remove the connections from the float assembly micro switches. Mark them to ensure you can reconnect them correctly after repairs. WIRING DIAGRAM The wiring diagram is attached to the back of the lower cover.
LDF9810ST DISHWASHER STEAM GENERATOR Squeeze the hose clamps and remove the 3 hoses from the steam generator. Remove 2 screws to take out the steam generator. NOTE: Be careful in case the steam generator is still hot or has hot water in it.
LDF9810ST DISHWASHER SUMP ASSEMBLY Remove the wiring connections, including the ground wires attached by screws. Remove the hose connections. Lift the sump assembly out of the base of the dishwasher. Remove the 2 screws and sump holder clips. Be careful not to let the sump assembly fall into the tub.
LDF9810ST DISHWASHER SOIL SENSOR Lift the retaining clips and pull the soil sensor (turbidity sensor) from the sump. REASSEMBLY When reassembling the sump. be careful to avoid kinking or damaging the small seals and gaskets inside it. (See page 39 in the exploded view.)
LDF9810ST DISHWASHER CUTLERY RACK RAIL Insert a screwdriver in the gap behind the rail at the back end and pry the end cap off. It is easily broken, so have a replacement available. UPPER RACK RAIL Pull the upper rack out until it stops.
LDF9810ST DISHWASHER SERIAL NUMBERS [Example] 801KW3400251 8 0 1 K W 0 0 2 5 1 Production Number [Internal code] Made in Korea Manufactured January 2008 New Serial Code (ETA Mid 2008) 12345 KR 406 YP 000002 + Options Sequential number...
LDF9810ST DISHWASHER OHM’S LAW and WATT’S LAW P = WATTS I = AMPERES Watts = Volts x Ohms Amperes = Volts / Ohms Watts = Amperes x Ohms Amperes = Watts / Volts Watts = Volts x Amperes Amperes = E I •...
LDF9810ST DISHWASHER SERVICE BULLETINS The bulletins included here were current and accurate at the time this manual was printed. The servicer is encouraged to check GCSC regularly for new and updated bulletins. LDF9810ST Page 47 DISHWASHER...
Need help?
Do you have a question about the LDF9810ST and is the answer not in the manual?
Questions and answers