Table of Contents
Advertisement
5 .
Place regulator onto the automatic valve on the gas cylinder . Push down regulator valve handle firmly and vertically .
(Figure B)
6 .
You should hear a "click" sound when the regulator is securely latched .
W CAUTION: Never attempt to connect regulator when the regulator valve is not in the "OFF"
position.
Operating Regulator
1 .
To turn regulator ON, turn the regulator valve handle clockwise into the the "ON" position . (Figure D)
2 .
To turn regulator OFF, turn the regulator valve handle counterclockwise into the the "OFF" position .
(Figure C)
Disconnecting Gas Cylinder
•
1 .
Make sure control knobs are
(OFF) position (Figure 1) .
2 .
Turn the regulator valve handle to the "OFF" position (Figure C) .
3 .
Push down regulator valve handle firmly then pull the regulator clamp and regulator upwards (Figure E) .
Operation of Excess Flow Check Device
The regulator can be fitted with a safety device designed to automatically limit the gas escape in case of gas leak, which prevents the gas from
reaching the grill . The marking "excess flow" on the regulator identification label means that the regulator is provided with this option .
The "excess flow device" is likely to activate under the following condition .
•
Normal operating conditions .
Consumption of the gas fired appliance is higher that the regulator flow capacity . In such case, you should contact your
installer .
•
In case of pipe being torn off, proceed as follows:
1 .
Disconnect the regulator per the "Disconnect Gas Cylinder" section .
2 .
Re-fit the hose correctly .
3 .
Connect the regulator per the "Connect Gas Cylinder" section .
4 .
Turn the regulator valve to the "ON" position .
5 .
Wait a few seconds (20 seconds) before restarting the system .
To guarantee a proper operation of the excess flow device, the pipe that supplies gas to the consuming appliance shall be no more than 1 .5 meters in length .
Checking for Leaks
Burner Connections
1 .
Make sure the regulator hose and valve connections are securely fastened to the burner and the tank .
2 .
Visually check the connection between the burner/venturi tube and orifice .
Note: The brass nut should be 1/4 to 1/2 turn past tight . The regulator will rotate 360° even when the brass nt is tightened .
W WARNING: Failure to inspect this connection or follow these instructions could cause a fire or an
explosion which can cause death, serious bodily injury or damage to property.
3 .
Please refer to diagram for proper installation (Figure 2) .
4 .
If the burner/venturi tube does not rest flush to the orifice, as shown, please contact 0800 9520101 for assistance .
Tank/Gas Line Connection
1 .
Make 2-3 oz . of leak detection solution by mixing one part liquid dishwashing soap with three parts water .
2 .
Make sure control knobs are in the
3 .
Connect gas tank per "Installing Gas Cylinder" section .
4 .
To turn regulator ON, turn the regulator valve clockwise into the the "ON" position . (Figure D)
5 .
Spoon several drops of solution, or use a squirt bottle, at all "X" locations (Figures 2 and 3) .
a . If any bubbles appear, turn the regulator valve counterclockwise into the the "OFF" position . (Figure C) .
b . If you continue to see bubbles after several attempts, turn gas cylinder valve to "OFF" and disconnect gas cylinder, per
"Disconnect Gas Cylinder" section . Contact 0800 9520101 for assistance .
c . If no bubbles appear after one minute, turn gas cylinder valve to "CLOSED," wipe away solution and proceed .
First Use
1 .
Make sure all labels, packaging and protective films have been removed from the grill .
2 .
Remove manufacturing oils before cooking on this grill for the first time by operating the grill for at least 15 minutes on (HIGH)
with the lid closed . This will "heat clean" the internal parts and dissipate odors .
Lighting Instructions
W CAUTION: Keep outdoor gas cooking appliance area clear and free from combustible materials,
gasoline and other flammable vapors and liquids.
W CAUTION: Do NOT obstruct the flow of combustion and ventilation air.
W CAUTION: Check and clean burner/venturi tubes for insects and insect nests. A clogged tube can lead
to a fire.
W CAUTION: Attempting to light the burner with the lid closed may cause an explosion.
1 .
Open lid .
2 .
Check for obstructions of airflow to the burners . Spiders, insects and webs can clog the burner/venturi tube . A clogged burner tube
can lead to a fire .
3 .
Connect gas cylinder per "Installing Gas Cylinder" section .
4 .
Makesure the regulator/control knob is in the "OFF" postion . (Figure 1)
5 .
To turn regulator ON, turn the regulator valve handle clockwise into the the "ON" position . (Figure D)
W CAUTION: If you are unable to turn the regulator handle to the "ON" position, your regulator is not
properly connected. Do not force the handle to open. Remove the regualtor and repeat "Connect Gas
Cylinder" section.
6 .
Insert a long lit match close to the burners through the cooking grid and heat plate . Position lit match near side of the burner
(Figure 4) .
7 .
Ture the regulator / control knob to
8 .
After lighting, observe the burner flame . Make sure all burner ports are lit and flame height matches illustration (Figure 5) .
Gas Regulator (continued)
Operating Instructions
•
(OFF) position (Figure 1) .
(HIGH) .
CAUTION
W If you are unable to turn the regulator handle to
the "ON" position, your regulator is not properly
connected. Do not force the handle to open.
Remove the regulator and repeat "Connect Gas
Cylinder" section.
WARNING
W The regulator is NEVER to be left on the
cylinder without its being connected to
the grill, as the tear-off proof safety is not
designed to ensure the operation of the
cylinder valve.
Figure 1
Figure 2
Figure 3
X
X
X
Figure 4
Match
9
.
Figure E
.
X
X
Hide quick links:
Advertisement
Table of Contents
