Maverick PT-55 Instruction Manual

Instruc on Manual
Maverick Rain Drop Waterproof Digital Thermometer
Congratula ons on the purchase of your new Waterproof thermometer tested to IP67.
Your thermometer is able to be immersed in up to 3
FOLDABLE PROBE
POWER ON/OFF
Press bu on once to power on
Press & hold the bu on 3 seconds to turn off the thermometer.
C/F (CALIBRATION)
Press for Fahrenheit or Cen grade for temperature reading.
C/F
Press & hold bu on for 5 sec for Re-Calibra on)
C/F
MAX/MIN -CLEAR
Press once to Maximum temperature recorded;
press again to show Minimum temperature recorded.
Press and hold to erase the current Maximum
or Minimum temperature recorded
RESET
Press the bu on to reset the thermometer to factory default
HOLD / BACKLIGHT
Press once to hold temperature recorded,
press again to un-hold
Every press of this bu on turns on the backlight for 5 seconds
1. To insert the ba eries
Use a coin to open the ba ery door at the back of unit by turning it from LOCK to UNLOCK.
Insert Two CR2032 Lithium ba eries with + sign up. Fasten the ba ery door securely but do not over-turn.
(The water resistance features requires maintaining the rubber gasket evenly within the groove.)
2. Temperature Scale
To select temperature reading in Fahrenheit or Cen grade by pressing
3. Ge ng Started
Press bu on once to turn on the thermometer.
Press bu on once to show Maximum temperature recorded with showing "MAX" icon.
Press again to show Minimum temperature recorded with showing "MIN" icon.
Press and hold bu on again to erase the current Maximum or Minimum temperature
recorded. The LCD will show "---" to indicate the temperature record is erased.
Press bu on once lock the current temperature displayed on thermometer.
The LCD will show "HOLD" icon. Press again to release the locked temperature reading,
the "HOLD" icon will be off and back to current temperature display.
Backlight will be turned on for be er viewing.
Model no. PT-55
of water for up to 30 minutes.
C/F MAX/MIN
POWER
(Calibration) (Clear)
C/F
RESET
LIGHT / HOLD
DISPLAY
BATTERY DOOR
bu on.
C/F
USDA SAFE FOOD TEMPERATURES*
4. RE-CALIBRATION of Thermometer
- Make ice bath with 3 parts ice and 1 part cold water.
- Insert the probe p into center of ice bath.
- Press and hold bu on for 5 seconds un l the unit show "CAL"
C/F
- The thermometer will start calibra on range from -3C /+26.6F to +2C /+35.6F to an accurate 0C /+32F
Note: Water boils at 208 F/97.8 C at 2000 above sea level
5. Ba ery Status
When the voltage on ba ery is low, Low Ba ery Indicator will be shown on LCD.
Please replace with new ba eries.
6. Manual / Auto Power Off
- Press and hold bu on for 3 seconds to turn off the thermometer for power saving
- Press bu on again to turn on the thermometer
- The thermometer will automa cally power off if no bu ons are pressed for ten minutes.
SPECIFICATIONS:
Opera ng Range : -4°F to 572°F / -20°C to +300°C
Display Range : -4°F to 572°F / -20°C to +300°C
Power : 2 x CR2032
CARE OF YOUR PRODUCT
Don't touch the probe p with bare fingers a er use to avoid burning fingers.
Although this thermometer is waterproof do not wash in dishwasher.
Don't put the thermometer probe inside the oven or microwave oven and always keep at least 6"
away from any heat source.
The thermometer probe is made of food-grade stainless steel and is designed for instant
measurement only.
Don't measure temperatures above 300°C /572°F. Never burn probe directly over fire. Doing so ,
the thermometer screen will show " HI " and con nuously using at this temperature will cause
permanent probe damage,
Use damp cloth or sponge to clean the probe and dry thoroughly a er cooking,
Don't subject the thermometer to extreme temperatures, humidity or severe shock.
Don't clean the case with any corrosive materials such as perfume, alcohol or cleaning agent or abrasives.
Keep the ba eries, stainless steel probe away from children.