Related Manuals for Coemar ISPOT 1200 EB
Summary of Contents for Coemar ISPOT 1200 EB
- Page 1 manuale di istruzioni instructions manual 1^ edizione provvisoria, maggio 2004 provisionally edition, may 2004...
- Page 3 ISPOT 1200 EB numero di serie/serial number data di acquisto/date of purchase fornitore/retailer indirizzo/address cap/città/suburb provincia/capital city stato/state tel./fax/ Prendete nota, nello spazio apposito, dei dati relativi al modello e al rivenditore del vostro I-Spot 1200 EB: in caso di richiesta di informazioni, pezzi di ricambio, servizi di riparazione o altro ci permetteranno di assi- stervi con la massima rapidità...
-
Page 4: Table Of Contents
11.3. Quick guide to menu navigation 11.4. Rapid scrolling 12. Aligning the lamp in the optical path 13. Turning on the ISPOT 1200 EB with no articulated movement 14. Resetting the counter 15. Automatic realignment 16. DMX 512 signal functions 17. -
Page 5: Important Safety Information
Congratulations on having purchased a coemar product. You have assured yourself of a fixture of the highest quality, both in com- ponentry and in the technology used. We renew our invitation to you to complete the service information on the previous page, to expedite any request for service information or spares (in case of problems encountered either during, or subsequent to, installation). -
Page 6: Lamp: Installation And Replacement
4. Lamp: installation and replacement ISPOT 1200 EB utilises a Philips MSI 1200w/s or Osram HMI 1200W/s lamp rated at 1200W with a SFc10-4 lampbase. The lamp is available from your authorised coemar sales agent: Philips MSI 1200W/S Osram HMI 1200W/S coemar cod. - Page 7 4) Replace the lampholder assembly and the 4 screws removed in step 1.(see Fig.1) 5. Operating voltage The projector may operate at voltages including 208, 230 or 240 V. Coemar presets (barring specific requests) an operating voltage of 240v. The preset voltage is indicated on a sticker located on the base of the projector power on/off switch as shown in the diagram below.
-
Page 8: Installation
For truss mounted installations coemar includes 2 cam-lock mounting devices (A). You may fit the cam-locks in 2 different positions on the base of the ISPOT 1200 EB. The cam-lock fittings are of the type which need a 1/4 turn. To be used correctly the fittings must be correctly fitted with some care. -
Page 9: Operating Voltage And Frequency
We recommend the use of a safety chain fitted through the “B “slot of the ISPOT 1200 EB and to the suspension truss in order to avoid the fixture accidentally falling. If using an after-market safety chain not manufactured by coemar, ensure that it is of suffi- cient rating to hold the weight of the unit. -
Page 10: Signal Connection
Control signal is digital, and is transmitted via two pair screened ø0.5mm cable. Connection is serial, utilising XLR 3 or XLR5 male and female sockets located on the base of the ISPOT 1200 EB, labeled DMX 512 In and OUT (see diagram). -
Page 11: Powering Up
DMX addressing To ensure that each projector accesses the correct signal, it is necessary to correctly address each ISPOT 1200 EB. When powered up initially, each projector will show A001 indicating DMX address 1; a projector thus addressed will respond to commands on channels 1 to 24 from the DMX 512 controller. -
Page 12: Display Panel Functions
11. Display panel functions The display panel of ISPOT 1200 EB shows all the functions available; it is possible to change some of those parameters and to add some functions. Changing the setting made by coemar can vary the functions of the device so that it will not respond to the DMX 512 controller used to control it. -
Page 13: Measure And Test (Meas)
11.2. Measure and test (MEAS) The internal microprocessor of the ISPOT 1200 EB allows for several diagnostic and output parameters to be displayed. You may record, in this menu, the position in which the projector will come to rest when turned on with no dmx signal attached. -
Page 14: Quick Guide To Menu Navigation
+ o – S T O R enter 11.4. Rapid scrolling iSpot 1200 EB Via the display, it is possible to rapidly scroll through the various numbers displayed in the menu which apply to the following 3 uses: 1) Pressing down and holding the + or - buttons will cause the numbers to scroll more quickly than by simply pressing buttons repea-... -
Page 15: Aligning The Lamp In The Optical Path
12. Aligning the lamp in the optical path Aligning the lamp in the optical system is achieved via the 3 adjusters at the rear of the projector. This procedure should be under- taken to properly align the lamp in the optical system and to avoid the possible overheating of the internal components due to the incorrect focusing of the beam onto components not intended to be exposed to this. -
Page 16: Resetting The Counter
Turning on the ISPOT 1200 EB without articulated movement This function may be useful should you need to power up the ISPOT 1200 EB inside its roadcase or for any other reason where you may wish to power up the unit without it moving. -
Page 17: Dmx 512 Signal Functions
16. DMX 512 signal functions If you have correctly followed all the steps described up to this point, your DMX 512 controller will allow you complete control of all the functions of the ISPOT 1200 EB as described in the following table: channel... - Page 18 channel type of function effect decimal percentage control fine indexing of the proportional fine indexing of the gobo (gobo wheel 1) 0 - 255 0% - 100% gobos 16 bit step no effect 0 - 10 0% - 4% continuous rotation of the gobo in a clockwise direction with proportional 11 - 131 4% - 51%...
- Page 19 channel type of function effect decimal percentage control proportional proportional control of the percentage of cyan colour in the light beam 21 19 cyan 0 - 255 0% - 100% from 0 to 100% proportional control of the percentage of magenta colour in the light 22 20 magenta proportional...
-
Page 20: Opening Up The Projector
17. Opening up the projector By removing the fixture’ s housing, complete access is available to the internals of the projector. Attention Always remove mains power prior to accessing the internal components of the projector. Base housing Use a Philip’ s head screwdriver to remove the 4 screws which affix the front and rear base housings, as shown in the following dia- gram. -
Page 21: Gobo Positioning
18. Gobo positioning The diagrams below illustrate how to correctly position the various types of gobos. Treated side facing the lamp Untreated side facing the projector front Textured side facing the lamp Smooth side facing the projector front Reflective side facing the lamp Treated side facing the projector front Positive image / readable text facing the lamp Negative image / reversed text facing the projector front... -
Page 22: Interchanging Gobos
19. Interchanging gobos ISPOT 1200 EB utilises a mechanical system which allows the fixture’ s gobos to be removed without the need for specialised equip- ment. Replacement gobos should be made of either heat resistant glass or metal. An ever-increasing range of gobos is available from your coemar sales network. - Page 23 A) replacing gobos on gobo wheel 1: use a tool such as a screwdriver as a lever on the spring on the inside of the gobo wheel (see fig.1), lifting it from its seat (see fig.2), after which you can remove the gobo. Place the new gobo into position and reverse the above procedure, ensuring that the spring sits firmly back in its proper place (see fig.3) Fig.1 Fig.2...
-
Page 24: Selecting The Transformer Voltage
60Hz 5) Close up the base with the housing covers as they were originally. 6) As shown in the diagram below, make a note on the outside of the ISPOT 1200 EB the new voltage which you have selec- ted. -
Page 25: Thermal Protection
Check all electrical components for correct earthing and proper attachment of all connectors, refastening if necessary. fuse replacement Locate the fuse, which protects the lamp and electronics, on the base panel of the ISPOT 1200 EB. Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type if necessary.. -
Page 26: Electronic Motor Alignment
This section is reserved only for technical and specialist personnel. The display panel of the ISPOT 1200 EB allows for the electronic alignment of the projector’ s motors in the optical system. This procedure is performed by coemar at the factory. It may be useful to perform this procedure in the case of internal components being replaced. -
Page 27: Error Messages
EPER: EEPROM Error The EEPROM is either defective or absent; refer to your coemar service centre for a replacement component. DTER: DATAQ Error The initial parameter settings are incorrect or corrupt;... -
Page 28: Troubleshooting
26. Parti di ricambio All the components of the ISPOT 1200 EB are available as replacement spares from your authorised coemar sales agent. Accurate description of the fixture, model number, and type will assist us in providing for your requirements in an efficient and effec- tive manner. - Page 29 Inghilterra 46042 Castelgoffredo (Mantova) Italy Tel. 0376/77521 Fax 0376/780657 Coemar si riserva il diritto di apportare modifiche senza preavviso. Coemar reserves the right to effect modifications without notification manuale istruzioni instruction manual ISPOT 1200 EB 1^ edizione provvisoria Maggio 2004...
Need help?
Do you have a question about the ISPOT 1200 EB and is the answer not in the manual?
Questions and answers