Rear Panel - B&K P/N13445 Owner's Manual

9 8
B K
&
S B
IMPLY ETTER!
C O N T R O L I / O
CONTROL IN ALLOWS AMPLIFIER
OPERATION WHEN A 5-24V SIGNAL I N P U T 1 I N P U T 1
IS APPLIED WITH A 3.5mm MINI JACK
C T R L C T R L
I N I N +
X L R ( B A L A N C E D )
C T R L C T R L
O U T O U T
1 2 V D C 1 2 V D C
1 2 5 m A 1 2 5 m A
R C A ( U N B A L A N C E D )
F U S E
F U S E
C A U T I O N : F O R C O N T I N U E D
P R O T E C T I O N A G A I N S T R I S K
O F F I R E R E P L A C E O N LY W I T H
S A M E T Y P E A N D R AT I N G .
C H A N N E L 1
O U T P U T
P L U S
+
-
A C L I N E
C A U T I O N
R I S K O F E L E C T R I C S H O C K R I S K O F E L E C T R I C S H O C K
D O N O T O P E N D O N O T O P E N
1
2
1. AC Fuse Holder - holds the AC Line fuse. This fuse is a 15 Amp / 250 Volt Slow Bow fuse. Replace only with
the same type and value fuse.
2. AC Input Receptacle - for attaching the supplied AC power cord to the amplifier.
3. Speaker Outputs - for connecting the speakers to the amplifier. Explained further on page 6.
4. Speaker Fuses - for protection against amplifier damage in the case of shorted speaker wires. Replace fuse
with the same type and value 6 AMP T-Lag. *The Reference 200.5 does not have amplifier channels 6 & 7.
5. Balanced Input - for connecting signal patch cables (interconnects) from the preamplifier to the amplifier.
Explained further on Page 4. *The Reference 200.5 does not have amplifier channels 6 & 7.
6. RCA Input - for connecting signal patch cables (interconnects) from the preamplifier to the amplifier. Explained
further on Page 4. *The Reference 200.5 does not have amplifier channels 6 & 7.
7. Balanced/Unbalanced Input Select - this switch is used to configure an AMPLIFIER PAIR for use as either
balanced (XLR) or RCA unbalanced line inputs. This switch controls two amplifier channels and allows signal
patch cables (interconnects) to be sourced from either balanced or unbalanced, preamplifier/processor or line
outputs. Explained further on Page 4. *The Reference 200.5 does not have amplifier channels 6 & 7.
8. Amplifier Control Input/Output - provides remote switching of the amplifier's standby on/off feature.
Explained further on page 8.

REAR PANEL

I N P U T 2 I N P U T 2 I N P U T 3 I N P U T 3
X L R ( B A L A N C E D )
R C A ( U N B A L A N C E D )
C H A N N E L 2 C H A N N E L 3
O U T P U T O U T P U T
M I N U S P L U S M I N U S P L U S M I N U S
+ +
- - -
I N P U T 4 I N P U T 4 I N P U T 5 I N P U T 5
X L R ( B A L A N C E D )
R C A ( U N B A L A N C E D )
C H A N N E L 4 C H A N N E L 5
O U T P U T O U T P U T
P L U S M I N U S P L U S M I N U S
+ +
- -
S E R I A L #
3
3
* *
7 6
I N P U T 6 I N P U T 6 I N P U T 7 I N P U T 7
X L R ( B A L A N C E D )
R C A ( U N B A L A N C E D )
C H A N N E L 6 C H A N N E L 7
O U T P U T O U T P U T
P L U S M I N U S P L U S M I N U S
+ +
- -
B&K Components, Ltd. B&K Components, Ltd.
Made in the U.S.A. Made in the U.S.A.
www.bkcomp.com
*
5
*
4