Pyronix DELTABELL-WE Installation Manual

Installation Steps: Step 1
Slide the
PCB
module
DELTABELL-WE
upwards.
The sprung
Self Powered External Sounder
back-tamper
Installation guide
arm can be
retracted to
allow removal.
This must be
done in order to
install the revolving
guides - see step 3.
Place the base on a
flat surface and
ensure it is vertical
using the spirit level
that is already installed. Drill and plug in each of the
fixing locations. The revolving guides will correct any
misalignment. If the Deltabell WE must be mounted
on an uneven surface, it is recommended that a
tamper levelling screw is used to ensure correct
back-tamper operation. See step 2.
RINS1433-3
Step 4
Place the PCB module, ensuring that the arrow is aligned with the marker (on the left of
the module). Expose the terminals by releasing the latch on the top of the PCB module.
NOTE: The bottom battery holder should be
installed as shown -in order to allow to
installation or removal of the Deltabell
Module.

Printed Circuit Board

Learn button
LEARN

Battery

BATT1 BATT2
Connectors
Optional
auxillary 12
volt PSU input
Sounder
SOUNDER
TAMPER
Tamper
LED OFF
COMFORT
LEDS
LED ON
Comfort LED
Enable/Disable
link
PLEASE
NOTE:
The auxillary
12V PSU input
Comfort LEDs
is not polarity
conscious
Tamper
levelling
screw
Mounting the
Deltabell WE on an
uneven surface
may cause false
triggering, through
incorrect operation of
the back-tamper.
A POZI number 2 screw
driver is recommended for
adjusting back tamper screw.
NOTE: This is for wall mounting only.
Step 5
Fit the lid by sliding its
hinges into place. The lid
can be supported in the
fully open position. To
close the lid, apply a
little force to push the lid
past the holds.
Close the cover, ensure
the tamper is operating
correctly, insert the
25mm long screw
supplied and rotate the
screw cover to a close.
*Lid sold separately
Battery
The batteries supplied have been
chosen to provide long service life
whilst, for safety reasons, having
limited output current. Replace
Red LED
only with approved batteries.
Blue LED
Green LED
To prevent possible damage to
components, any static charge on
your body needs to be eliminated
before touching the inside of the
unit. This can be accomplished by
Strobe
touching some grounded/earthed
metallic conductor such as a
radiator/pipework immediately
before replacing batteries.
Step 2
Tamper switch
For electrical products sold within Low voltage Threshold:
the European Community. At the Batt1: 2.2V +/-5% at 25 C,
end of the electrical products life, it Batt2: 2.5V +/-5% at 25 C
Batteries: 2x 3V 5AHr
should not be disposed of with
Lithium battery packs (BATT-ES1)
household waste. Please recycle
where facilities exist. Check with Acoustic output: Tone.
your Local Authority or retailer for Strobe duration: 10ms
recycling advice in your country. Strobe Frequency: 1Hz
Sound pressure level: 101dBA
When disposing of Max sound duration: 15 mins
the product, the Dimensions: 290 x 285 x 50 mm
battery must be Selectable comfort LEDs:
removed and 4 second flash rate
disposed of Operation from external PSU (optional):
separately in 11V to 14V
accordance with the IMPORTANT NOTE: The batteries should
local regulations still be connected if using an external PSU.
Case Tamper.
Step 3
Insert the guides as shown. Make sure that the guides 'B'
are aligned with the tabs to the right (this is so the PCB
module slides in). Turn each guide until they line up with the
drilled holes, while referencing the spirit level for the correct
alignment, and fix the base firmly to the wall.
Please note, if the Deltabell
WE is installed on an uneven
surface, it is recommended
that you do not tighten up
the wall screws until after
the module is installed
(step 4)
NOTE: Older Deltabell products were supplied with a single cylindrical
battery type (1x BATT-CR34615D) instead of the two square batteries
(2x BATT-ES1) in the current product. The different battery types are
NOT INTERCHANGEABLE between products.
Replace like with like under all circumstances.

Learning the DELTABELL-WE onto the Control Panel

When you are ready to learn the device to the The three coloured LEDs give a
control panel receiving equipment, and when visual indication of the signal
the equipment is in the learn mode (see the strength.
Control Panel Programming Manual) follow the
procedure below. Green indicates good signal strength
and is a good location to install.
1. Make sure the battery is installed correctly
2. Press and hold the Learn button until the Red indicates poor signal
3 LEDs start cycling through the different strength and the device should not
colours, then release. be installed in that position.
3. The device is correctly learnt when the
green LED flashes. If no LED illuminates then the device
is completely out of range.
Please see the Enforcer 32-WE user,
The blue LED will illuminate when the
programming and quick set up manuals for
device is activated.
further information
Technical Specification Warranty and compliance
WARRANTY: This product is sold subject to our standard
warranty against defects in workmanship for a period of two
years (batteries excluded). Please note: In positions where
the Deltabell WE casing is subjected to high levels of U.V.
sunlight, there may be risk of case colour fading, this is not
covered by the warranty. In the interest of continuing
improvement of quality, customer care and design, Pyronix
Ltd reserve the right to amend specifications without giving
prior notice.
Pyronix Ltd, Braithwell Way, Hellaby,
Rotherham, South Yorkshire, S66 8QY
Customer support: +44(0)845 6434 999
(local rate) or +44(0)1709 535225
Hours: Mon to Fri, 8.00am till 6:30pm
Email: customer.support@pyronix.com
Reverse polarity protected
Website: www.pyronix.com
The batteries and battery holder
should be inserted as shown:
RED BLUE GREEN
RED BLUE GREEN
RED BLUE GREEN
RED BLUE GREEN
RED BLUE GREEN
EN50131-4:2009
EN50131-5-3:2005+A1:2008
Security Grade 2
Environmental Class IV