Table of Contents
Advertisement
Quick Links
Installing / Service Company
Monitoring Station
Master Code
"Quick Arm"
"Chime"
02
03
04
05
06
07
Exit Delay Time
Entry Delay Time
Fire Alarm Sound (check one)
Burglar Alarm Sound (check one)
ZONE DESCRIPTIONS -
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 5
ZONE 6
SPECIAL CODES
Duress Code
AUXILIARY CODES
08
09
10
11
12
13
14
SYSTEM NOTES
Secondary Exit Delay Time
Secondary Entry Delay Time
9
Steady Siren
9
Yelp Siren
U
CHECK FIRE ZONES
1
9
Pulsing Bell
9
Steady Bell
Fire
Fire
Fire
Fire
Advertisement
Table of Contents
Related Manuals for CADDX Ranger 7600
Summary of Contents for CADDX Ranger 7600
- Page 1 Installing / Service Company Monitoring Station SPECIAL CODES Master Code Duress Code AUXILIARY CODES "Quick Arm" "Chime" SYSTEM NOTES Exit Delay Time Secondary Exit Delay Time Entry Delay Time Secondary Entry Delay Time Fire Alarm Sound (check one) Steady Siren Pulsing Bell Burglar Alarm Sound (check one) Yelp Siren...
- Page 2 THIS MANUAL IS FURNISHED TO HELP YOU UNDERSTAND YOUR SECURITY SYSTEM AND BECOME PROFICIENT IN ITS OPERATION. ALL USERS OF YOUR SECURITY SYSTEM SHOULD READ AND FOLLOW THE INSTRUCTIONS AND PRECAUTIONS IN THIS BOOKLET. FAILURE TO DO SO COULD RESULT IN THE SECURITY SYSTEM NOT WORKING PROPERLY.
-
Page 3: How To Bypass Zones
HOW TO ARM YOUR SECURITY SYSTEM To Arm the security system, close all of the protected doors and windows. The green "READY" light on the keypad control will be illuminated when all of the protected zones and sensors are secure. If any of the zones are bypassed, a sensor in that zone can be violated without affecting the "READY"... -
Page 4: Automatic Arming Option
AUTOMATIC BYPASS OPTION If checked, the "AUTOMATIC BYPASS" option has been selected by your installing company. With this feature enabled, all interior zones will automatically bypass if you "ARM" your security system and do not leave through a designated entry/exit door. The "AUTOMATIC BYPASS"... -
Page 5: Fire Zone
TURNING ON THE CHIME FEATURE If checked, your security system will operate in the "CHIME" mode, allowing the monitoring of pre-designated zones while the security system is not armed. While in the "CHIME" mode, the opening of any of these zones will produce a 1 second beep from the keypad control. To activate this feature, press [ 1 ] for "CHIME"... -
Page 6: Duress Code
DURESS CODE If checked, your security system has a "DURESS CODE" option. If so, this code may be programmed to send a special message to the central monitoring station if you are forced to arm or disarm your security system against your will. Check with your Installing/Servicing company to see if this option has been enabled for your system. -
Page 7: Keypad Control Tones (Beeps)
KEYPAD CONTROL LIGHT INDICATORS ARMED RED: On when system is armed; off otherwise. Flashes for alarm memory if alarm was activated during arming cycle. READY GREEN: On when all zones are secure or and/or Bypassed and the system is ready to arm; off otherwise. INSTANT RED: On when the entry/exit zones are instant;... -
Page 8: Emergency Evacuation Plans
EMERGENCY EVACUATION PLANS An emergency evacuation plan should be established for an actual fire alarm condition. For example, the following steps are recommended by the National Fire Protection Association and can be used as a guide in establishing an evacuation plan for your building. Draw up a floor plan of your home. -
Page 9: System Notes
SYSTEM NOTES... - Page 10 7600 USER’S MANUAL 7600UE98 REV E (02-10-98)
Need help?
Do you have a question about the Ranger 7600 and is the answer not in the manual?
Questions and answers