Salus VS20WRF Installer's/User's Manual

4 in 1 Digital Thermostat RF
Models: VS20WRF and VS20BRF
VS10WRF and VS10BRF
I N S T A L L E R / U S E R M A N U A L
SALUS Controls plc
SALUS House
Dodworth Business Park South,
Whinby Road, Dodworth,
Barnsley S75 3SP, UK.
Sales: T: +44 (0) 1226 323961
E: sales@salus-tech.com
Technical: T: +44 (0) 1226 323961
E: tech@salus-tech.com
www.salus-controls.com
SALUS Controls is a member of the Computime Group
Maintaining a policy of continuous product development, SALUS Controls plc
reserves the right to change specification, design and materials of products listed in
this brochure without prior notice.
Product Compliance
This product complies with the essential requirements and other relevant provisions of Directives
2014/30/EU, 2014/53/EU and 2011/65/EU. The full text of the EU Declaration of Conformity is available at
the following internet address: www.saluslegal.com.
Safety Information
Use in accordance with the regulations.
Indoor use only.
Keep your device completely dry.
Disconnect your device before cleaning it with a dry cloth.
Always isolate the AC Mains supply before installing or working on any components that require 230 VAC 50Hz supply.
Introduction
Thank you for purchasing the SALUS 4 in 1 room thermostat it must be used with the Universal Gateway
UGE600 (purchased separately) when having an Internet connection or with the KL08RF for the underfloor
system withoul Internet connection. The Universal Gateway allows communication with other devices in
the iT600 RF system range. Other Zigbee devices include wiring centre, system receiver & TRV. You can
use your iT600 system with the Salus Smart HomeApp. Available on Google Play and App Store.
KL10RF
KL08RF
CO10RF
RX10RF (optional for an underfloor
system, mandatory for a TRV system)
Installation – Terminal Connections VS10WRF
1
Power Terminals 230 Vac
Understanding your terminal connections
Used for supplying power to
Rear of unit
the unit. 230V supply can be
sourced from the wiring centre
or any convenient source.
Sensor Terminals
2
Can be used for external AIR,
Floor sensor when configured
1
as thermostat. Can also be used
for Cylinder thermostat when
2
configured for HW.
Installation – First Power Up
The following screens show examples only
MCU software version
*Please note that 88.8 and
will be shown
8.8 are a reference to the
software version.
Please make sure that your Universal Gateway is installed. You can use it with both internet and non internet connection.
The LED will be blue when connected to the internet and red when it's not connected.
With Internet
Without Internet
If you are installing an underfloor system without an Internet connection, you can use the coordinator from the
KL08RF instead of the Universal Gateway.
Installation – Power Up your devices
Please follow the installation procedure for all equipment. After installation, your devices should look like this:
Pairing with Wiring Center (KL08RF) with Internet connection
1
2
TRV10RF
TRV10RFM
4
5
Tap Scan for equipment when you
want to start adding equipment
to the App. The gateway will start
flashing red.
Pairing with Wiring Center (KL08RF) with Internet connection
6
7
ZIGBEE software version
9 10
will be shown
12
Please follow the on screen instruction in order to complete the pairing process.
Pairing with Wiring Center (KL08RF) without Internet connection
5 sec
5 sec
1
2
4 5
7
5 sec
3
5 sec
Pairing the TRV with Internet connection
8
1
11
4
6
OR
3
6
8
10
OR
12
2 3
5
Tap Scan for equipment when you
want to start adding equipment
to the App. The gateway will start
flashing red.
7
Wait until the LED is solid red.
Press the Open/Close button
once. When the initialization
process is complete, the LED will
go off.
Press and hold the for
10 seconds until the TRV starts
flashing red.
9
11