Advertisement
WARNING! Dispose of spent battery correctly and in accordance with local regulations as it contains acid.
DANGER! DO NOT attempt to dismantle the battery pack. For safety and environmental reasons DO NOT discard in domestic waste or by
burning. ONLY discard or recycle according to local waste authority regulations.
WARNING! DO NOT allow a leaking battery to come into contact with skin. If contact with battery fluid occurs take immediate action:
a) Skin contact: Wash immediately with soap and water.
b) Eye contact: Flush eye immediately with cool, clean running water for at least 15 minutes and seek immediate professional medical
attention.
2. INTRODUCTION
Twin daylight fluorescent tubes suitable for applications where mains power is unavailable. Tubes can be selected to run individually or as a pair
from rechargeable cells. Includes an integrally stored mains cable for recharging only, electronic control allows unit to be used as an emergency
light, switching on the light in the event of mains power failure. Features carry handle and floor stand, can also be wall mounted.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ML18/36
Tubes:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 x 20W
Tube Length: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 590mm
Supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V
Battery: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6V 4.5Ah
Operating Time: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Tube; 3hr, 2 Tubes; 1.5hr
Consumable Parts:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 003-SD1824D - Tube
4. OPERATION
4.1.
CHARGING THE UNIT.
4.1.1. The unit will charge when plugged into mains supply regardless of function switch position. To achieve fastest charge put function switch to
the 'OFF' position.
4.1.2. Open the power cable compartment at the back of the light. Uncoil the power cable and plug it into the mains power supply. The red LED
will light to indicate the presence of mains power.
4.1.3. The battery pack will take approximately 20 hours to charge initially. Subsequent charging times will depend on the state of discharge of the
battery pack.
4.1.4. When charging is complete unplug the mains power cable and stow it back in the compartment.
4.2.
USING THE Light.
4.2.1. Select the required tube combination using the function switch. The function switch has three positions:-
1 Tube - OFF -
4.2.2. The light will function as an emergency light if the function switch is placed in either the 1 or 2 tube position whilst connected to the mains.
In case of a mains electricity failure, the selected number of tubes will light. Restoration of mains power will switch the light off again.
4.2.3. After a full charge the light will run for approximately 1hr 30min on two tubes and 3hrs on one tube.
NOTE! The green LED will illuminate whenever a tube should be lit. If the tubes DO NOT light and the green LED is illuminated,
suspect an unserviceable tube. The light has a TEST button feature to test the tubes. When the TEST button is pressed the
tubes should light up if connected to the mains. If any tubes fail to light up, they are likely to be unserviceable.
5. MAINTENANCE
WARNING! Before replacing the fluorescent tubes or performing any maintenance the unit must be unplugged from the mains. Allow the
tubes to cool before touching them.
WARNING! DO NOT turn the unit on with the transparent cover removed or with the tubes removed.
5.1.
CHANGING THE FLUORESCENT TUBES.
5.1.1. Replacement tubes must be the same type and rating as the original tubes supplied.
5.1.2. Remove the transparent cover by removing the two cover screws and lifting it away.
5.1.3. Each tube can be removed by rotating it in either direction until one of the connector pins appears at the top of the tube holder slot. Lift out
the old tube and replace it with a new one. Push the new tube all the way into the tube holder slots at both ends and then rotate the tube a
quarter of a turn in either direction.
5.1.4. Ensure that the tubes are correctly installed and seated before switching on.
5.2.
CLEANING.
5.2.1. Clean the unit with a damp cloth and a mild soapy solution. Do not use solvents or abrasive cleaners.
© Jack Sealey Limited
Both Tubes
Original Language Version
ML18/36.V3 Issue: 4 - 104/04/17
Advertisement
