Download Print this page
Lumenier LUX User Manual

Lumenier LUX User Manual

Flight controller
Hide thumbs Also See for LUX:

Advertisement

FLIGHT CONTROLLER
FLIGHT CONTROLLER
FLIGHT CONTROLLER
FLIGHT CONTROLLER
VERSION 1.1
© LUMENIER 2016

Advertisement

loading
Need help?

Need help?

Do you have a question about the LUX and is the answer not in the manual?

Questions and answers

Summary of Contents for Lumenier LUX

  • Page 1 FLIGHT CONTROLLER FLIGHT CONTROLLER FLIGHT CONTROLLER FLIGHT CONTROLLER VERSION 1.1 © LUMENIER 2016...
  • Page 2 Lumenier website opensource.lumenier.com. Trademarks Trademarks Trademarks Trademarks LUMENIER and the LUMENIER logo are registered trademarks of FPV MANUALS, LLC. • All other trademarks and copyrights are the property of their respective owners. •...
  • Page 3: Table Of Contents

    TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS Getting Started Getting Started Advanced Features Advanced Features Getting Started Getting Started Advanced Features Advanced Features Board Layout PID/OSD Stick Tuning Pins/Configuration Troubleshooting Troubleshooting Troubleshooting Troubleshooting Package Contents Device Specifications Firmware Upgrade Basics...
  • Page 4: Getting Started

    GETTING STARTED GETTING STARTED GETTING STARTED GETTING STARTED Board Layout Board Layout Board Layout Board Layout F F F F unction unction unction unction G G G G Ground 2 2 2 2 PWM Output (Motor 2) RX Input (PPM,S.BUS, SUMD / 3.3-5v / GND) Receiver Voltage (3.3v-5v) 5v 5v B B B B Z+...
  • Page 5 Bridge PPM for PPM. SRX for SBUS, SUMD, other serial connections The accelerometer and gyroscope need to initialize every time the board is given power. Do not disturb the LUX LUX board or your quad while powering on. • Do not disturb the LUX LUX board or your quad while plugging in.
  • Page 6: Package Contents

    MPU6500 MEMS gyro/accelerometer • STM32 DFU mode for bootloader + software • Up to 26v (6S lipo) input • 5v 1.0A output • 3v/5v RX Voltage Output Selectable • Do not use LUX LUX for unintended applications such as commercial aerial photography.
  • Page 7: Basics

    OpenLog serial data loggers work over simple serial connections and support microSD cards up to 64GB. Your LUX LUX flight controller has 3 3 3 3 separate hardware serial (U U U U ART ART) TX/RX pin pairs. Connect VCC/TX/RX/GND to corresponding pins labeled T1/R1/T2/R2/T3/R3 T1/R1/T2/R2/T3/R3.
  • Page 8 Main Power connection) Main Power connection) Your LUX LUX flight controller has input voltage 6-26v (2-6S lipo). Connect main power lead to pins labeled 10 Always check the polarity before plugging in. There is no reverse polarity protection. Enable feature in CLI: feature VBAT...
  • Page 9 Your Lumenier LUX LUX has a Micro-USB connector. Hold the “boot” button while plugging in for the first time. The LUX has two modes. It switches to “DFU” mode while the “boot” button is pressed as it is plugged in.
  • Page 10 MW OSD MW OSD Your LUX LUX flight controller can be programmed via stick positions, using your OSD (On Screen Display) to display and change settings. To access the OSD menu, make sure your LUX LUX board is disarmed. Move the Throttle...
  • Page 11: Troubleshooting

    STM32 DFU MODE STM32 DFU MODE Your LUX LUX board can always be recovered and restored to factory defaults should you ever encounter software issues. Simply hold the “boot” button on your LUX LUX board while plugging in the USB cable. You can release the button after plugging LUX LUX into your computer.