ShoreTel SG-220T1 Quick Install Manual

Introduction
The ShoreGear T1/E1 Voice Switch package contains:
• ShoreGear T1 / E1 Voice Switch (SG-220T1, SG-T1k, SG-220E1, or SG-E1k)
• Power cord
• Stick-on feet for surface installation
• Mounting Ears - attachable installation brackets
About The ShoreGear T1/E1 Voice Switches
Each ShoreGear T1/E1 Voice Switch connects internal extensions or IP phones to a
central office (CO) digital trunk line.
The switch provides connectivity through:
• Two RJ-45 LAN connectors
• One RJ-45 Telco port for connecting the switch to a telephone company line
• One RJ-45 Monitor port for connecting test equipment
• One DB-9 (female), RS-232C maintenance port (19200 bps, 8 bits, no parity, 1 stop
bit, no handshake) for serial communications
• One audio input port (3.5 mm stereo) for connecting to a music-on-hold source
• One audio output port (3.5 mm stereo) for connecting to a corporate paging system
or night bell
Audio Input Port
(music on hold)
Status Network LAN 1
LED LEDs Connector T1 LEDs
Default
Switch
Power Network RS-232C
LED LEDs Maintentance
Port
Monitor
Audio Output Port LAN 2
Port
(night bell) Connector
Audio Input Port
(music on hold)
Status Network LAN 1
E1 LEDs
LED LEDs Connector
Default
Switch
Power Network RS-232C
LED LEDs Maintentance
Port
Audio Output Port LAN 2 Monitor
(night bell) Connector Port
Installation
Installation Equipment
To install the switch, you need the following equipment:
• AC surge protector for the power connection
• RJ-45 cables for connecting the switch to the local area network and telco lines
• Music-on-hold source with a standard mini-headphone Y-adapter (optional)
• #1 Phillips screwdriver
Installation Location Requirements
To ensure optimum operating conditions for the SG-T1/E1 voice switch, verify the
operating environment is adequately ventilated, free of gas or airborne particles, and
isolated from electrical noise.
Installing an SG-T1/E1 Switch in a 19-inch Rack
An SG-T1/E1 switch is placed in a 19-inch rack only by mounting a ShoreGear Dual Tray
into the rack, then installing the SG-T1/E1 into the Tray. You can install an SG-T1/E1
switch on the left or right side of the tray.
Refer to the Quick Install Guide for the ShoreGear Dual Tray for Tray installation
instructions and information on using the tray.
ShoreGear 220T1
or ShoreGear T1k
Telco Mounting the ShoreGear Voice Switch on a Flat Surface
Port
If you plan to mount the switch on a flat surface, first attach the provided rubber feet
to the bottom corners of the device. (You can stack up to three switches in a surface
installation.)
German: Das ShoreGear Voice-Schaltgerät auf einer ebenen
Oberfläche montieren
Wenn Sie planen, das Gerät auf einer ebenen Oberfläche zu montieren, befestigen Sie
zunächst die mitgelieferten Gummifüße an den unteren Ecken des Geräts. (Bei einer
Oberflächeninstallation können Sie bis zu drei Schaltgeräte übereinander stapeln.)
Servicing Procedures
WARNING: SG-T1/E1 switches contain no internal field serviceable parts. Return the
ShoreGear 220E1
equipment to ShoreTel for any required service procedures.
or ShoreGear E1k
Telco
CAUTION: Internal fuses should be serviced only by qualified ShoreTel personnel. If
Port
internal fuses are blown and require replacement, return the SG-T1/E1 switch to ShoreTel
for service.
WARTUNGSVERFAHREN
ACHTUNG: SG-T1/E1 enthält keine internen Teile, die vor Ort gewartet werden können.
Senden Sie das Gerät an ShoreTel, falls Wartungsarbeiten erforderlich sein sollten.
VORSICHT: Interne Sicherungen dürfen nur von qualifizierten ShoreTel-Mitarbeitern
gewartet werden. Wenn interne Sicherungen ausgetauscht werden müssen, senden Sie
den SG-T1/E1 zur Wartung an ShoreTel.
Connections
Connecting the ShoreGear Voice Switch to the Network
Once the SG-T1/E1 Voice Switch is secured to a rack or surface-
mounted, you can connect it to the data network.
Use an RJ-45 Ethernet cable to connect one or both of the LAN
ports to the network subnet.
While both ports can detect and respond to link status, the switch
uses only one LAN port at a time.
Powering on the ShoreGear Voice Switch
After connecting the switch to the network, power on the device by connecting it to an
AC power source.
1. Plug an AC surge protector (not provided) into a grounded AC power source.
2. Plug one end of the provided power cord into the receptacle on the back of the
switch, then plug the other end into the AC surge protector.
The power LED flashes momentarily, and remains lit.
• If the LED is not lit, make sure the power cord is plugged into the switch and the
power source.
• If the LED continues flashing, there is an internal error. Unplug the switch to power
it off, then power it back on. Refer to the "Configuring Switches" chapter in the
ShoreTel Administration Guide for information on flash patterns, or contact the
ShoreTel Support Services at http://www.shoretel.com.
The LAN ports auto-sense the network transport rate. When the network connection is
established, the network LED indicates a transport rate of 10 Mbps or 100 Mbps, and
whether the switch is receiving and transmitting data.
Optional Connections
After connecting the voice switch to the LAN, you can make optional
connections, including input from a music-on-hold source or output
to your internal paging system.
1. Connect a music-on-hold source (CD player or other audio
source) to the audio input port.
2. Connect your site' s paging system to the audio output port.
Connecting a T1 or E1 Line
After setting up the network connections and configuring the SG-T1/
E1 Voice Switch for operations, you can connect your T1 (SG-220T1
or SG-T1k) or E1 (SG-220E1 or SG-E1k) line to the switch.
Use an RJ-45 T1 cable to connect your T1 or E1 line to the Telco port.
For detailed information on switch port and trunk configuration, see the
sections "Configuring Switches" and "Configuring Trunks" in the Shore-
Tel Administration Guide.