Flip the GSMVLP5-4G/GSMVLP5CN-4G circuit board
over and reinstall it in the plastic housing.
Route the cable so it is not pinched by the plastic or
damaged by the mounting screws.
Install the two screws that secure the circuit board to the
Reinstall the GSMVLP5-4G/GSMVLP5CN-4G
Install the GSMVLP5-4G/GSMVLP5CN-4G in the control.
Ensure that the connector board is properly seated into
the receptacle on the control and the GSM-EXT cable is
routed properly as shown.
Secure the GSMVLP5-4G/GSMVLP5CN-4G in the
control with the three screws.
Route the external antenna cable through the control
rear case and connect the coaxial connector to the GSM-
Route the GSM-EXT cable and secure it to the tie wrap
point on the control with the provided tie wrap as shown.
Mount the external antenna. Refer to the Installation
Instructions provided with the AlarmNet GSM-ANT
Reconnect the battery connector to the receptacle on the
After the wiring connection has been made, snap the
front and back case closed.
Plus the power supply into a 24-hour, 110VAC
REFER TO THE INSTALLATION AND SETUP GUIDE FOR THE CONTROL WITH WHICH THIS DEVICE IS USED FOR WARRANTY
INFORMATION AND LIMITATIONS OF THE ENTIRE SYSTEM.
FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized
changes or modifications could void the user's authority to operate the equipment.
FCC CLASS B STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's
instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device
in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential
installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the radio or television receiver away from the receiver/control.
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.
• Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA CLASS B STATEMENT
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and RSS 210 of IC. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes:
(1) Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit accepter toute interference reçue y compris les interferences causant une
WARNING: The GSMVLP5-4G/GSMVLP5CN-4G must be installed to provide a separation distance of at least 20 cm
from all persons.
800-10843 1/12 Rev. A
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2012 Honeywell International Inc.