Spectra 1641 Installer's Manual

1641 LCD KEYPAD V1.0 (RUSSIAN / LITHUANIAN) - INSTALLER'S GUIDE
The 1641 LCD Keypad includes a programmable 32-character LCD screen, zone input and a PGM output as w ell as supp orting the u se of
the Paradox Memory Key. All of the LCD key pad's f eatures and options can only be accessed through the keypad's prog ramming mode.
During the key pad's power up, press and hold the [
STEP 1:
STEP 2:
STEP 3:

[1] Labels

This f eature allows y ou to program some of the messages that appear on the key pad's LCD screen. In step 3 of "Entering Keypad
Programming Mode" described in the shaded box abov e, select option [1]. The keypad will prompt you to enter a 3-dig it section. E ach
section f rom [101] to [135] represents a specif ic message. Enter the 3-digit section that correspond s to the me ssage you wish to cha nge.
[101] - [116] = Zone 1 to Zone 16
[133] = Partition 1
[134] = Partition 2
[135] = Key pad Name (def ault: "Spectra Family ")
KEY
X1
A
[1]
Д
[2]
З
[3]
Л
[4]
П
[5]
У
[6]
Ч
[7]
Ы
[8]
Я
[9]
[0] SPACE

[2] Options

In step 3 of "Entering Key pad Programming Mode", select option [2]. Y ou will now be able to enable or disable the keypad's option s as
shown in table 2. Press the corresponding key s until all desired options are set, and then press [
Key Description
[1] Keypad Zoning Sending
Keypad Zone Requires 1k Ohm EOL Resistor
[2]
Keypad Zone Set to
[3]
On-Board Keypad Tamper Supervision
[4]
Status LED Follows Arming Status of
[5]
Multiple Zone Display (status of several zones on one screen without zone label)
[6]
Scrolling Zone Display (each screen displays zone label and status of one zone)
[7]
For Future Use
[8]
] key to set the LCD screen and the Key pad Code to def ault.
CLEAR
Entering Keypad Program ming M ode
Press and hold the [0] key f or two seconds.
Enter the [ ]. Default:000000

KEYPAD CODE

Press the key corresponding to the desired option or use the arrow ke ys to
scroll through the av ailable options and press [
[1] = Labels
[2] = Options
[3] = Key pad Code
Cursor indicates the selected character. Press the [ ] or [
characters. Press the numerical key s f rom [0] to [9] to replace the selected
character. Ref er to table 1.
Table 1: Character Reference
[UC] Mode
X2 X3 X4 X1
Б B Г
A
Е Ё Ж
D
И Й К
G
М Н О
J
Р С Т
M
Ф Х Ц
P
Ш Щ Ъ
S
Ь Э Ю
V
! & ,
Y
/
' : +
Table 2: Keypad Options
].
ENTER
[4] = Key pad PGM
[5] = Read Key
[6] = Write Key
Indicates current character sty le.
Press the [FNC2] key to change
between [UC], [LC] and [SP]. See Table 1.
[101] TEXT {UC}
tab
ZONE ONE
[LC] Mode
X2 X3 X4
B C 1
E F 2
H I 3
K L 4
N O 5
Q R 6
T U 7
W X 8
Z . 9
- = 0
OFF
Disabled
NO (default)
Keypad Zone 1 (default)
Disabled (default)
Partition 1 (default)
Disabled (default)
Disabled (only if [6]=ON)
N/A
[SP] Mode
X1 X2 X3 X4
a б в г
д е ё ж
з и й к
л м н о
п р с т
у ф х ц
ч ш щ ъ
ы ь э ю
я #
↑ ↓
( ) < >
].
ENT ER
ON
Enabled (default)
Yes
Keypad Zone 2
Enabled
Partition 2
Enabled
Enabled (default)
N/A
] key s to scroll the