Advertisement
DCS
CORTO 350, 550, 750
CORTO-C
2. PRe WiRing - COnTinUed.
• For masonry walls using an angle grinder and masonry cutting disc,
cut a 25mm deep slot from the cable leg to the eventual location of the
transformer, see Fig 2.0
• Place the supplied low voltage wiring in the slot created and render over
INSTALLATION INSTRUCTIONS
directly.
• Black poly tube is supplied to locate the wire in the correct position. Conduit
PRE WIRING – CONTINUED
may also be used but is not essential.
• For masonry walls using an angle grinder and masonry cutting disc, cut a 25mm deep slot from the cable leg to the eventual location
• Low voltage wiring tails should protrude from the finished lined wall approx
of the transformer, see Fig 2.0.
150mm to allow for trimming.
• Place the supplied low voltage wiring in the slot created and render over directly.
• Black polytube is supplied to locate the wire in the correct position. Conduit may also be used but is not essential.
3. TOWel Rail assemBlY
• Low voltage wiring tails should protrude from the finished lined wall approx 150mm to allow for trimming.
• Fix the legs to the towel rail using the stainless steel machine screws and
3. TOWEL RAIL ASSEMBLY
spring washer supplied. See Fig 3.0
0, 550, 750
• Fix the legs to the towel rail using the stainless steel machine screws and spring washers supplied. See Fig 3.0
• The small grub screw holes must face, what will be, the BOTTOM of the
• The small grub screw holes must face, what will be, the BOTTOM of the towel rail.
towel rail.
4. TOWEL RAIL FIXING / CONNECTION
TinUed.
• If a wirenut is accidentally removed, it may be reconnected with the spare waterproof wirenut connector provided. Waterproof wirenuts
3. TOWel Rail COnneCTiOn
ng an angle grinder and masonry cutting disc,
MUST NOT BE REUSED.
• Fix the polycarbonate rectangular bushes to the wall using the screws
from the cable leg to the eventual location of the
• Fix the round polycarbonate bushes to the wall using the screws provided. DO NOT substitute other screws. In particular, DO NOT
provided. DO NOT substitute other screws. In particular, DO NOT use
0
use countersunk head screws less than 50mm long.
countersunk head screws less than 50mm long. See Fig 4.0
voltage wiring in the slot created and render over
• Use the towel rail as a guide to determine the correct position for the bushes. MAKE SURE IT IS LEVEL.
• Use the towel rail as a guide to determine the correct position for the bushes
• Make the electrical connection to the towel rail using the waterproof wirenut connectors provided. See Fig 7.0
or use the fixing dimensions Table 1.0. MAKE SURE IT IS LEVEL.
• The connectors and excess wiring should be pushed back into the leg of the towel rail and/or into the wall.
plied to locate the wire in the correct position. Conduit
• Make the electrical connection to the towel rail using the waterproof wirenut
• If there is a concern that water may enter into the wall cavity, neutral cure silicone sealant may be applied around the cable where it
is not essential.
exits the wall lining.
connectors provided. See Fig 7.0
s should protrude from the finished lined wall approx
• Finally, fix the towel rail in position using the self tapping grub screws provided. See Fig 5.0
Waterproof wirenuts MUST NOT BE REUSED. A spare is included.
mming.
• The connectors and excess wiring should be pushed back into the leg of
5. TIMER AND SWITCH
the towel rail.
mBlY
• The towel rail must have a switch in the bathroom that can be identified as the towel rail switch. This is typically a separate switch
• If there is a concern that water may enter into the wall cavity, neutral cure
el rail using the stainless steel machine screws and
mechanism on the light switch plate for the bathroom. eg. 3 gang switch plate – lights – extractor – towel rail.
silicone sealant may be applied around the cable where it exits the wall
d. See Fig 3.0
• The supplied 'ECOTIMER' is a 230 – 240V device that should be installed behind the switchplate between the switch and the transformer.
lining.
holes must face, what will be, the BOTTOM of the
See Fig 6.0.
• Finally, fix the towel rail in position using the small stainless steel screws
provided. See Fig 5.0
• Note: Drilling a 2mm pilot hole makes it much easier to screw in the
eCTiOn
Screw fixing approx 14mm
self tapping screws. The bushes are moulded from glass reinforced
rectangular bushes to the wall using the screws
from cable hole centre
e
polycarbonate and are very hard.
bstitute other screws. In particular, DO NOT use
ews less than 50mm long. See Fig 4.0
er
5. TimeR and sWiTCH
guide to determine the correct position for the bushes
• The towel rail must have a switch in the bathroom that can be identified
nsions Table 1.0. MAKE SURE IT IS LEVEL.
onduit
as the towel rail switch. This is typically a separate switch mechanism on
nnection to the towel rail using the waterproof wirenut
the light switch plate for the bathroom. eg. 3 gang switch plate - lights -
See Fig 7.0
prox
extractor - towel rail
MUST NOT BE REUSED. A spare is included.
10mm
• The supplied 'ECOTIMER' is a 230 - 240V device that should be installed
xcess wiring should be pushed back into the leg of
hole
behind the switchplate between the switch and the transformer. See Fig 6.0
at water may enter into the wall cavity, neutral cure
and
e applied around the cable where it exits the wall
he
FIGURE 4
l in position using the small stainless steel screws
Fig 4.0
ilot hole makes it much easier to screw in the
he bushes are moulded from glass reinforced
very hard.
ELECTRICIANS please ensure a copy of the installation
H
instructions is left with the end user for future reference.
Electricians, please ensure a copy of the installation
bushes
ve a switch in the bathroom that can be identified
instructions is left with the end user for future reference
h. This is typically a separate switch mechanism on
irenut
or the bathroom. eg. 3 gang switch plate - lights -
650, 850
Screw fixing approx 14mm
from cable hole centre
10mm
hole
page 3 of 5
Fig 4.0
FIGURE 5
Fig 5.0
Towel Rail
Towel Rail
Towel Rail
Transformer
page 3 of 5
Fig 4.0
Fig 5.0
FIGURE 6
Fig 6.0
CORTO-C INSTALLATION GUIDE | PAGE
12 Volt
N
Mains
L
page 3 of 5
Screw fixing approx 14mm
from cable hole centre
10mm
hole
Towel Rail
Towel Rail
Towel Rail
12 Volt
Transformer
N
Mains
L
Red
Ecotimer
Blue
Brown
Wall Switch
3 OF 6
Advertisement
