Binding Function; Switch Transmitter Channel; Maintenance, Care And Repair - RC Logger RC EYE One Operating Instructions Manual

12. BINDING FUNCTION

The remote control transmitter and the model are coupled with a special encrypted transmitter signal. This is
referred to as "binding" of the two components that warranty widely interference-free operation. Transmitter
DQG PRGHO DUH ERXQG H[ ZRUNV DOUHDG\ 2XWHU LQÀXHQFHV HJ VWURQJ LQWHUIHUHQFH HPLVVLRQ PD\ FDXVH
loss of binding. In this case the "RC EYE One" would no longer react to the transmitter signal (LED in the
model is permanently lit).
To bind your transmitter to your model again, proceed as follows:
1. Connect the battery to the "RC EYE One".
2. 3XVK WKH EXWWRQ IRU ÀLJKW PRGH VHOHFWLRQ IRU PRUH WKDQ WKUHH VHFRQGV 7KH /(' LQ WKH PRGHO QRZ ÀDVKHV
red/green alternately.
3. Push the on/off button for more than three seconds with the transmitter switched off. The transmitter
tarts beeping rhythmically.
4. The transmitter and model scan for each other and reconcile their data. After successful binding, the
/(' LQ WKH PRGHO ÀDVKHV LQ WKH ODVW ÀLJKW PRGH VHOHFWHG 7KH ³5& (<( 2QH´ LV UHDG\ WR VWDUW DJDLQ

13. SWITCH TRANSMITTER CHANNEL

7KH WUDQVPLWWHU RI WKH ³5& (<( 2QH´ PD\ EH SURJUDPPHG WR ¿YH GLIIHUHQW WUDQVPLWWHU FKDQQHOV 7KLV
SHUPLWV FRQFXUUHQW RSHUDWLRQ RI XS WR ¿YH WUDQVPLWWHUV DQG ³5& (<( 2QH´
You may also need to select another transmitter channel if you experience inference from other devices with
915 MHz-technology on the channel that is set (e.g. weather stations, radio headphones, etc.). Proceed as
follows for programming another transmitter channel:
1. Switch off the transmitter.
2. Push the button for channel selection for more than three seconds. A sound signal is emitted. The
number of sound signals indicates the transmitter channel number. A sound signal means transmitter
channel 1, two sounds signals mean transmitter channel 2, etc.
3. Now release the button. Then push the button repeatedly until the desired transmitter channel (e.g. 3
sound signals = transmitter channel 3) is set.
4. &RQ¿UP WKH QHZ WUDQVPLWWHU FKDQQHO E\ SXVKLQJ WKH RQRII EXWWRQ 7KH SURJUDPPLQJ LV FRQ¿UPHG E\ D
single sound signal.
5. Now bind the transmitter and model as described in chapter BINDING FUNCTION.

14. MAINTENANCE, CARE AND REPAIR

Regular Cleaning
7KH ³³5& (<( 2QH´´ LV D YHU\ VLPSOH EXW QRQHWKHOHVV ZHOOGHVLJQHG À\LQJ GHYLFH 7KHUH DUH QR PHFKDQLFDO
SDUWV WKDW QHHG WR EH OXEULFDWHG RU UHTXLUH VSHFLDO PDLQWHQDQFH +RZHYHU DIWHU HDFK ÀLJKW RSHUDWLRQ \RX
should clean the ""RC EYE One"" of possible dirt (wool strings, dust, etc.).
For cleaning, use a dry or slightly damp cloth and avoid contact between water and the electronics,
rechargeable battery and motors.
24