Table of Contents
Advertisement
Quick Links
Pneumatic Floor Nailer / Stapler
User Manual
[Revision 1.0 December 2017]
READ THIS MANUAL CAREFULLY BEFORE USE AND KEEP FOR FUTURE REFERENCE – FAILURE TO DO SO
MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY VOID WARRANTY. • Products covered by this manual
may vary in appearance, assembly, inclusions, specifications, description and packaging.
E&OE
©2017 Unimac
Advertisement
Table of Contents
Related Manuals for Unimac NALFLRUMCA2XH
Summary of Contents for Unimac NALFLRUMCA2XH
- Page 1 READ THIS MANUAL CAREFULLY BEFORE USE AND KEEP FOR FUTURE REFERENCE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY VOID WARRANTY. • Products covered by this manual may vary in appearance, assembly, inclusions, specifications, description and packaging. E&OE ©2017 Unimac...
-
Page 2: Safety
• For specific equipment safety use and dust extraction / collection facilities, and vents. ensure these are connected and used care, see Equipment Safety. properly. Dust collection can reduce dust-related hazards. E&OE © 2017 Unimac... - Page 3 • Do NOT make adjustments while the power lines. Electrical shock can be fatal. equipment is running. • Perform service related activities in suitable conditions, such as a workshop. • Replace worn, damaged or missing warning/safety labels immediately. E&OE © 2017 Unimac...
-
Page 4: Safety Symbols
Wear appropriate Always wait for moving parts injury to fingers, limbs, blood clothing and protectiove to stop fully before handling etc. Take due care when devices. the product, adjusting, handling and using the maintenence etc. product. E&OE © 2017 Unimac... - Page 5 Carry hook to load – do NOT Laser may be in use – do NOT Wear appropriate eye throw or run. protection for welding. Dorect look directly at laser, or allow exposure to weld arcs may others to. cause permanent eye injury. E&OE © 2017 Unimac...
-
Page 6: Equipment Safety
• Do NOT connect the tool to air pressures potentially exceeding 200PSI (13.8 bar). • Remove all fasteners from the tool before connecting it to the air supply. The tool driving mechanism E&OE © 2017 Unimac... - Page 7 Do NOT use the tool as a hammer for aligning floor boards etc. Transportation Safety • Always remove all fasteners from the tool before transporting or working on it (adjusting etc). • Always disconnect the tool from the air supply before transporting or working on it. E&OE © 2017 Unimac...
-
Page 8: Table Of Contents
Operation ............................. 10 Air Supply..........................10 Loading Fasteners ........................10 Nailing and Stapling ........................ 11 Removing Jammed Fasteners ....................11 Maintenance and Troubleshooting .................... 13 Daily Cleaning / Inspection ...................... 13 Troubleshooting ........................13 Specifications ..........................14 E&OE © 2017 Unimac... -
Page 9: Parts Identification
Tools / Accessories (may be supplied) (not shown) O-ring and gasket set (for technician use) Top Handle Mallet Air Inlet Replacement Board Foot Air Tool Lubricating Oil Centre Handle 3 / 4 / 5mm Allen Key Activator Multi-Purpose Spanner E&OE © 2017 Unimac... -
Page 10: Operation
• Load nails down one side of the rail (B), with the "L" part of the head on the rail in the magazine. Close the magazine cover until it locks in place. Reconnect the tool to the air supply. Loading Staples Loading Nails E&OE © 2017 Unimac... -
Page 11: Nailing And Stapling
4. After removing the jammed fasteners, re-install the fastener guide plate and board stop, then load the magazine and re-connect the tool to the air supply. E&OE © 2017 Unimac... - Page 12 Pneumatic Floor Nailer / Stapler E&OE © 2017 Unimac...
-
Page 13: Maintenance And Troubleshooting
Tighten screws. Nail magazine is dirty. Clean nail magazine. Pusher spring damaged. Replace spring. Driver is worn or damaged. replace. Other problems Contact your local service centre. E&OE © 2017 Unimac... -
Page 14: Specifications
16 Gauge 25mm - 50mm (1" – 2") Staple Capacity Nail Capacity L-Shaped Nail Size 16 Gauge 37mm – 50mm (1 ½ – 2") ¼” NPT Air Supply Connector Air Consumption 4.5 CFM Net Weight 6kg approximately E&OE © 2017 Unimac... - Page 15 ©2017 Unimac. All rights reserved. No part of this document, including descriptive content, concepts, ideas, diagrams or images may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, scanning or recording, or any information storage and retrieval system, without express permission or consent from the publisher.