Advertisement
Step 4:
Audio Notification
The AXON flex camera emits beeping sounds called audio prompts to notify you of
the system status. These audio prompts usually occur after you perform an action
with the controller.
Operating Mode
Powering on or off
Recording an event
Press the battery button while the camera is
recording
The device is ending an event and returning to
BUFFERING mode
The controller battery is at 20% capacity or
lower
The system is in buffering mode
Cable disconnect (camera will shut down)
Camera's memory is full (camera will not record)
Step 6:
Camera Upload Status LED
System Status
Initial connection (momentary)
In queue awaiting upload
Uploading data
Device ready (all videos uploaded successfully)
Device not assigned, agency mismatch, camera set in the offline mode, or device error
EVIDENCE.com Dock has no communication with the camera
Firmware update, internal battery charging, extremely low battery, or memory full
Network error
Transfer error, device re-trying to transfer
Step 7:
Using AXON Mobile
The AXON Mobile application enables you to replay video and add metadata (GPS,
title, case ID, and category) to your videos using a smart phone or multimedia player.
1
Using your smart device, download the AXON Mobile application from the
Google Play store or the iTunes App Store. Search AXON
Mobile.
2
On your smart device, open the AXON Mobile application
and follow the onscreen instructions for Bluetooth pairing.
See diagram below (or see Step 8: Pairing an AXON flex
camera with a Smart Device).
3
To add categories to your videos you will need to sign into
your agency. In the AXON Mobile app go to the Settings
menu, select Agency, enter your email address and select
your agency. You will now be able to add categories to your
AXON flex videos. (Must be connected to Internet.)
Note: All data is stored on the AXON flex camera. No
videos are stored on your smart device.
For more information, see the AXON flex System User Manual, EVIDENCE.com Dock Quick Start Guide, AXON Mobile for Android Devices User Manual, or AXON Mobile for
IOS Devices User Manual, available at www.TASER.com, au.TASER.com, uk.TASER.com.
Bluetooth is a trademark of the Bluetooth SIG, Inc. Google Play is a trademark of Google, Inc. iTunes is a trademark of Apple, Inc. IOS is a trademark of Cisco Systems, Inc. Windows is a
trademark of Microsoft Corporation. TASER is a trademark of TASER International, Inc. registered in AU, CA, the EU, NZ, ZA and the US. © is a trademark of TASER International, Inc.
registered in AU, the EU and the US. ® is a trademark of TASER International, Inc. registered in AU, CA, the EU, ZA and the US. AXON is a trademark of TASER International, Inc., registered
in AU, the EU, HK, SG and the US. All rights reserved. AXON flex is a trademark of TASER International, Inc., registered in AU, the EU, MY and the US. All rights reserved.
Audio Notifications
One beep
Two beeps (sound every two
minutes)
Two beeps
One long beep
Four quick beeps (repeating
every 20 seconds)
No beeps
One beep
Three beeps
When you plug your camera into the EVIDENCE.com Dock, the LED on the camera displays the system's status.
Step 5:
Recharging the Battery and Uploading Data
If you do not have an EVIDENCE.com Dock, upload video with a Windows compatible
computer using EVIDENCE Sync: TASER.com/syncdownload.
1
Ensure the controller is off. Insert the camera and controller into the EVIDENCE.
com Dock as shown.
The EVIDENCE.com Dock automatically uploads the data to EVIDENCE.com.
When a video uploads successfully to EVIDENCE.com, that video is removed
from the camera. (The camera must be registered to your EVIDENCE.com
account.)
2
At the beginning of the next shift, ensure that
your camera (if one has been assigned to you)
displays with a green LED before removing it
from the EVIDENCE.com Dock.
Camera bottom LED indication
Solid red (for 20 seconds or fewer)
Solid yellow
Blinking yellow – DO NOT remove the camera from the EVIDENCE.com Dock
Solid green
Blinking red
LED off
Blinking red and yellow – DO NOT remove the camera from the EVIDENCE.com Dock
Blinking red, yellow, and then green
Blinking green and yellow
Step 8:
Pairing an AXON flex Camera with a Smart Device
1
While holding down the volume/pairing button, move the ON/OFF switch on
the AXON flex controller to the ON position.
2
Wait until you hear 3 beeps. The pairing LED will blink green.
3
Release the volume/pairing button.
4
Using your smart device's Bluetooth settings, pair with the AXON flex camera.
5
You will hear 3 beeps when devices are paired. The AXON flex system will then
go into BUFFERING mode.
Flex Camera
Power Switch
Red = On/Buffering
Flex Controller
Blinking Green Pairing LED
Pairing/Volume Button
1
Hold down pairing/volume button
2
Turn on AXON flex controller
3
Pairing LED will blink green; you will
hear 3 beeps
MPC0146 Rev: A
Advertisement
