Service LC1500 / Manual LCD TV/Monitor TABLE OF CONTENTS SECTION PAGE 1. SPECIFICATIONS......................... 1 2. PRECAUTION..........................2 3. ADJUSTMENT INSTRUCTION..................... 3 4. DESCRIPTION OF BLOCK......................5 5. TROUBLESHOOTING ........................ 15 6. BLOCK DIAGRAM ........................16 7. REPLACEMENT PARTS LIST ....................16 8.
Page 2
Parts for your MARANTZ equipment are generally available to our National Marantz Subsidiary or Agent. ORDERING PARTS : Parts can be ordered either by mail or by Fax.. In both cases, the correct part number has to be specifi ed.
PRECAUTION WARNING WARNING FOR THE SAFETY-RELATED COMPONENT. BE CAREFUL ELECTRIC SHOCK ! There are some special components used in LCD • monitor that are important for safety. These parts are If you want to replace with the new backlight (CCFL) or •...
ADJUSTMENT INSTRUCTION 1. Application Object 3-3. White Adjustment (1) Approve the signal of 64 tones of XGA(1024 * 768). This instruction is for the application to the LCD TV. (2) Select all the gain of R, B and G with using ADJ of remote control.
Page 9
1-4. Pin Description Pin No. Pin Name Type Conneciton(if not used) Short Description B1/CB1IN VREF Blue1/Cb1 Analog Component Input G1/Y1IN VREF Green1/Y1 Analog Component Input R1/CR1IN VREF Red1/Cr1 Analog Component Input B2/CB2IN VREF Blue2/Cb2 Analog Component Input G2/Y2IN VREF Green2/Y2 Analog Component Input R2/CR2IN VREF Red2/Cr2 Analog Component Input...
Page 10
Pin No. Pin Name Type Conneciton(if not used) Short Description Picture Bus Chroma Picture Bus Chroma Picture Bus Chroma V SUPC SUPPLYD Supply Voltage, Chroma Output Circuitry GND C SUPPLYD Ground, Chroma Output Circuitry Picture Bus Chroma Picture Bus Chroma Picture Bus Chroma Picture Bus Chroma(LSB) GND SY...
Page 12
2-2. Pin Description Pin No. Pin Name Type Conneciton(if not used) Short Description Not connected I2C_CL IN/OUT I2C clock I2C_DA IN/OUT I2C data I2C_CL IN/OUT I2S clock I2S_WS IN/OUT I2S clock I2S_DA_OUT I2S word strobe I2S_DA_IN1 I2S data output ADR_DA I2S1 data input ADR_WS ADR data output...
Page 13
Pin No. Pin Name Type Conneciton(if not used) Short Description Picture Bus Chroma Picture Bus Chroma Picture Bus Chroma V SUPC SUPPLYD Supply Voltage, Chroma Output Circuitry GND C SUPPLYD Ground, Chroma Output Circuitry Picture Bus Chroma Picture Bus Chroma Picture Bus Chroma Picture Bus Chroma(LSB) GND SY...
Page 14
3. MX88L284(LCD Monitor Controller) 3-1. Features • • On-chip gamma correction for panel compensation Input Converts NTSC/PAL and PC video signal into flat panel • PC video up to 1024X768@85Hz, and 1280X1024@60Hz display device timing and resolution. • operation mode Provide full frame buffer, reduce frame buffer and frame •...
Page 15
4. AD9884A(Analog Flat Panel Interface) 4-3. Block Diagram 4-1. Features • 140 MSPS Maximum Conversion Rate • 500 MHz Analog Bandwidth AD9884A • 0.5 V to 1.0 V Analog Input Range OUTA CLAMP • 400 ps p-p PLL Clock Jitter •...
Page 16
4-5. Pin Description Signal Type Name Function Value Package Pin Inputs Analog Input for RED Channel 0.5V to 1.0V FS Analog Input for GREEN Channel 0.5V to 1.0V FS Analog Input for BLUE Channel 0.5V to 1.0V FS HSYNC Horizontal Sync Input 3.3V CMOS COAST Clock Generator Coast Input(Optional)
TROUBLESHOOTING 1. General Features Symptom Cause Check Point Soft touch doesnÕt Defective speaker wire 1) Make some space between the speaker wire and function properly and inverter wire the Soft touch Board by sticking the speaker wire to the guide hole of the cabinet. 2) Arrange working state of A1.
DESCRIPTION LOCA. NO PART NO DESCRIPTION Q114 0TR387500AA TR,CHIP 2SC3875S(ALY) KEC Q116 0TR387500AA TR,CHIP 2SC3875S(ALY) KEC IC101 IC,MARANTZ (refer REPLACEMENT PARTS LIST) Q117 0TR387500AA TR,CHIP 2SC3875S(ALY) KEC 0IAL241610B IC,AT24C16-10PC-2.7 8PIN DIP ST E IC102 TR,CHIP 2SC3875S(ALY) KEC Q301 0TR387500AA IC104...
Page 21
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film in the P/No. means as follows; CE : Electrolytic RN : Metal Film RF : Fusible LOCA.
Need help?
Do you have a question about the LC1500 and is the answer not in the manual?
Questions and answers