Paradigm PWSoundbar Setup Manual

ARC
™
7
(Anthem Room Correction)
Press (Scroll Down) to scroll down to the desired option, either Off or ON.
ARC – Anthem Room Correction: Factory Default = Off
Once the desired option is displayed, press
Enables or disables ARC ™ (Anthem Room Correction).
to select Off or ON.
To enable ARC ™ , please refer to the "ARC ™ (Anthem Room Correction)" section in the
Owner's Manual for the room calibration procedure.
Once ARC has been completed and the file uploaded it will automatically be enabled.
™
If the selection was successful the soundbar's display will indicate Saved.
Press (Menu) on the Remote or the soundbar's touch display.
Press (Scroll Down) to scroll down to the ARC submenu.
Press (Scroll Right) or (Select) to select the ARC submenu.
Power Settings:
9
Power Standby / Power On Volume / IP Control / Standby IP
POWER STANDBY: Factory Default = POWER ON VOL: Factory Default = -35dB IP CONTROL: Factory Default: On
Auto Standby
Adjusts default volume level of the Enables/disables the state of the IP
Configures the state of the soundbar's soundbar when initially powered on. control. This is only required if using an
power on/Off to Auto Standby or Always On. It can be adjusted from -90dB to +10dB*. Ethernet/Wi-Fi based home automation
system.
In Auto Standby the soundbar will power *Maximum volume (+10dB) is not advised.
down after 20 minutes if no signal is
detected.
To change the Power To change the Power–on Vol: To enable IP Control:
Standby option:
Press (Menu) on the Remote or the Press (Menu) on the Remote or the
soundbar's touch display. soundbar's touch display.
(Menu) on the Remote or the
Press
soundbar's touch display.
Press (Scroll Down) to scroll down to Press (Scroll Down) to scroll down to
Power Settings. Press (Scroll Right) Power Settings. Press
Press (Scroll Down) to scroll down to
or (Select) to select the Power Settings or (Select) to select the Power Settings
Power Settings. Press (Scroll Right)
submenu. submenu.
or (Select) to select the Power Settings
submenu.
(Scroll Down) to scroll down to
Press
Press (Scroll Down) to scroll down to IP
Power-on Vol. Press (Scroll Right) or
Press (Scroll Down) to scroll down to
Control. Press (Scroll Right) or
(Select) to select the Power-on Vol submenu.
Power Settings. Press (Scroll Right)
to select the IP Control submenu.
or (Select) to select the Power Standby
submenu.
Press (Scroll Down) to scroll down to the
desired option, either Set or Last Used. Press
Press (Scroll Down) to scroll down to the
(Scroll Right) or (Select) to select the
desired option, either Off or On. Once the
Press (Scroll Down) to scroll down to the
Set submenu.
desired option is displayed, press
desired option, either Auto Standby or Always
Right) or (Select) to select Off or On.
On.
Once the desired option is displayed, press
To decrease the Power-On Volume setting,
(Scroll Right) or (Select) to select Off
press (Volume Down). To increase the
or On.
Power-On Volume setting, press (Volume
Up). When the desired level is displayed,
If your selection was successful the
press (Scroll Right) or (Select) to select
soundbar's display will indicate Saved.
the desired level.
If your selection was successful the
If your selection was successful the
soundbar's display will indicate Saved.
soundbar's display will indicate Saved.
Wireless Setup
8
Wireless Setup
(Scroll Right) or (Select)
This setup option allows you to Initialize Wi-Fi (PW Soundbar ONLY) or
Bluetooth Pairing activation.
PW Soundbar ONLY:
IMPORTANT! We recommend using an Ethernet connection when connecting the soundbar
to your network. This is the most reliable setup method.
To configure a Wireless Network please refer to the DTS Play-Fi
Start Guide for complete instructions.
The connection methods vary between the Play-Fi app and AirPlay.
Learn Remote
10
STANDBY IP: Factory Default = Off Learn Remote
Requires IP Control to be enabled in
This function provides the ability to program a secondary remote. The soundbar will continue to
order to function.
respond to the original remote and any programmed secondary remote that you wish to use
simultaneously.
Standby IP allows the soundbar to receive
IP based commands while in standby
For a complete list of programmable functions, please refer to the "The Menu System" section
mode.
in the Owner's Manual.
If the operation was successful the display will indicate Saved.
If the operation was not successful the display will indicate Failed.
To enable Standby IP:
The operation will "Fail" if a command is already in use/programmed.
Press (Menu) on the Remote or the
soundbar's touch display.
Press (Scroll Down) to scroll down to
(Scroll Right) Power Settings. Press (Scroll Right)
or (Select) to select the Power Settings
submenu.
Press (Scroll Down) to scroll down to
(Select) Standby IP. Press (Scroll Right) or
(Select) to select the Standby IP submenu.
Press (Scroll Down) to scroll down to the
desired option, either Off or On. Once the
(Scroll (Scroll
desired option is displayed, press
Right) or (Select) to select Off or On.
If your selection was successful the
soundbar's display will indicate Saved.
Wireless Setup:
Press (Menu) on the Remote or the soundbar's touch display.
Press (Scroll Down) to scroll down to Wireless Setup. Press (Scroll Right) or
select the Wireless Setup submenu.
and Apple AirPlay Quick Press (Scroll Down) to scroll down to Initialize WiFi (PW Soundbar ONLY) or Bluetooth Pairing.
®
Press (Scroll Right) or (Select) to select the Initialize WiFi or Bluetooth Pairing submenu.
Initialize Wifi ONLY:
(Scroll Down) to scroll down to the desired option, either No or Yes.
Press
If you selected Yes, the soundbar's display will indicate Resetting.
If you selected No, the soundbar's display will indicate No Changes made.
Bluetooth Pairing ONLY:
The soundbar's display will now indicate pairing mode on.
To Learn (program) a new remote:
Press (Menu) on the Remote or the soundbar's touch display.
Press (Scroll Down) to scroll down to Learn Remote.
Press (Scroll Right) or (Select) to select the Learn Remote submenu.
(Scroll Down) to scroll down to the command you wish to program.
Press
Press (Scroll Right) or (Select) to select the command submenu (For example: Volume + > ).
Push Button will be displayed on the soundbar's display.
Holding the Secondary Remote remote approx 12" from the soundbar, push the button you wish
to program. The soundbar will then respond with "Push Button Again". Holding the Secondary
Remote remote approx 12" from the soundbar, push the button a second time to confirm.
If your selection was successful the soundbar's display will indicate Saved.
(Select) to

SETUP GUIDE

Step by step setup instructions to customize each setting.
Identifies functions and default features.
Operation
11
Source Name
This option allows users to create custom names for each input. Please refer to the 'Menu Option: Source Name' section in the Owner's Manual for further details regarding this menu.
Service
This submenu offers the ability to perform factory resets and displays information about your soundbar's current firmware versions & MAC addresses.
Press (Menu) on the Remote or the soundbar's touch display.
Press (Scroll Down) to scroll down to Service.
Press (Scroll Right) or (Select) to select the Service submenu.
Please refer to the 'Menu Option: Service' section in the Owner's Manual for further details regarding this submenu.
USB Upgrade
This menu option is used when performing a USB firmware update.
Press (Menu) on the Remote or the soundbar's touch display.
Press (Scroll Down) to scroll down to the USB Upgrade submenu.
Press (Scroll Right) or (Select) to select the USB Upgrade submenu.
Press (Scroll Down) to scroll down to Upgrade All.
POWER MENU MUTE
(Scroll Right) or (Select) to select Upgrade All. This will update your Soundbar's USB firmware.
Press
Please refer to the 'USB Update' section in the Owner's Manual for further details regarding USB firmware updates.
User Tips
BASS MODE
NIGHT NORMAL BASS +
Each button on the remote corresponds to its dedicated input on the soundbar.
To access a specific input, simply select the corresponding button on the remote.
HDMI 1 HDMI 2 HDMI 3
Pairing an additional device while on the Bluetooth input: Push & Hold the Bluetooth button on the remote for 4 seconds. The soundbar will emit a tone
HDMI ARC BLUETOOTH
confirming that the broadcast feature is now active and a new device can now be paired. Note! Once the tone is emitted, the original pairing will be cancelled along with the
media stream.
OPTICAL 1 OPTICAL 2
ANALOG 1 ANALOG 2 (PW Soundbar Only) Please refer to the Wireless Setup Guide for iOS and Mac Users for complete instructions on a Network Connection and playback via AirPlay.
Shown: Input Options on
Setting up Auto Power On Function (applies to North America ONLY):
Paradigm PW Soundbar
To enable the Auto Power On Function, navigate the menu to the following location: Power Settings > Standby IP Control > On. With this setting enabled, the soundbar will
remote.
power on when a signal is detected from the Digital Optical or RCA Inputs.
rev. 113016 | VQE1A875Z