Advertisement
Clip Plate
Figure 2-3 Fix the the Camera
6.Adjust the camera according to the figure below
to get an optimum angle.
°
°
0 ~360
°
°
0 ~360
°
°
0 ~75
Figure 2-4 3-axis Adjustment
2.2 Installation of Type
II
Camera
Steps:
1.Drill the screw holes and the cable hole on the
ceiling according to the supplied drill template.
Cable Hole
Screw Hole
Figure 2-5 The Drill Template
2.Fix the mounting base to the ceiling with the
supplied screws.
Figure 2-6 Fix the Mounting Base and Camera
3.Route the cables to the cable hole and connect
corresponding power cable and video cable.
4.Secure the camera to the mounting base.
5.Fix the enclosure to camera.
6.Attach the trim ring to the camera and rotate
it clockwise to secure the camera loosely.
°
°
0 ~360
°
°
0 ~75
°
°
0 ~360
Figure 2-7 3-axis Adjustment
7. Adjust the camera according to the figure 2-7 to
get an optimum angle and tighten the trim ring.
2.3 Installation of Type
Camera
III
Steps:
1.Drill the screw holes and the cable hole on the
ceiling according to the supplied drill template.
Cable Hole
Screw Hole
Figure 2-8 The Drill Template
2.Fix the mounting base to the ceiling with the
supplied screws.
Figure 2-9 Fix the Mounting Base and Camera
3.Route the cables to the cable hole and connect
corresponding power cable and video cable.
4.Secure the camera to the mounting base.
5. Adjust the camera according to the figure below
to get an optimum angle.
°
°
0 ~360
°
°
0 ~75
°
°
0 ~360
Figure 2-10 3-axis Adjustment
3 Menu Operation
VIDEO
AE
WB
DAY/NIGHT
RESET
EXIT
SETTING
BRIGHTNESS
MODE
CONTRAST
EXPOSURE MODE
INFRARED
SHARPNESS
AGC
SMART IR
SATURATION
DNR
MIRROR
Figure 3-1 Main Menu
With a coaxial camera controller (purchase
separately) or calling the preset No.95 you can
select the menu and adjust the camera parameters.
3.1 FORMAT
You can set the format as PAL/NTSC.
3.2 SET UP
Move the cursor to
SET UP
, and press menu button
to enter the SET UP sub menu.
3.2.1 AE
Move the cursor to AE, and you can adjust the
image brightness by the
BRIGHTNESS EXPOSURE
,
MODE
, and
AGC
.
Brightness
:
Brightness refers to the brightness of the image.
Exposure Mode:
Move the cursor to
Exposure Mode
, you can select
the exposure mode between
Globe
and
BLC
.
When BLC is selected as the exposure mode, the
level of BLC mode can be adjusted, as shown in the
Figure 3-2.
EXPOSURE
WB
MODE
MWB
5
1.BRIGHTNESS
2.EXPOSURE MODE
BLC
R GIAN
1-|--10
LEVEL
5
B GAIN
1-|--10
3.AGC
MIDDLE
8
RETURN
4.RETURN
Figure 3-3 WB
Figure 3-2 EXPOSURE
AGC:
AGC optimizes the clarity of image in poor light
scene. AGC level can be set as OFF, LOW, MIDDLE
and HIGH.
3.2.2 WB
Move the cursor to WB, and you can set White
Balance mode as
AWB
and
MWB
in this menu
AWB: white balance is being adjusted
automatically.
MWB
: Set the
R GAIN/B GAIN
As shown in Figure 3-3.
3.2.3 DAY & NIGHT
Move the cursor to DAY & NIGHT, and select
SAVE/EXIT
COLOR B/W
,
, or
SMART
as the DAY & NIGHT mode.
COLOR: The image is colored in day mode all the
time.
B/W
: The image is black & white all the time, and
the IR LED turns on in the low-light conditions.
SMART
: Select to turn on/off the INFRARED_LAMP
and to set the Smart IR level from 1to 16.
As shown in Figure 3-4.
DAY/NIGHT
MODE
INFRARED
SMART IR
RETURN
Figure 3-4 DAY/NIGHT
3.2.4 VIDEO SETTING
Contrast:
Contrast enhances the difference in color and light
between parts of an image.
You can set the value from 1 to
Sharpness:
Sharpness determines the amount of
detail that an imaging system can reproduce.
You can set the value from 1 to 10.
Saturation:
You can set the saturation level of the image. The
value is from 0 to 10.
DNR:
DNR decreases the noise effect, especially in low
light conditions and delivers more accurate and
sharp image quality. You can set the value from
0 to 7.
Mirror
:
You can set the Mirror status as H, V, HV, or OFF.
3.2.5 Reset
Reset all the settings to the default.
3.2.6 EXIT
Exit and Save & exit are selectable.
3.2.7 SAVE/EXIT
Move the cursor to
SAVE & Exit
save the settings and exit the menu.
.
value from 1 to 10.
SMART
OFF
0-|--5
8
.
10
, and press OK to
Advertisement
