VIDICON BINGO Installation Instructions

INSTALLATION INSTRUCTIONS
BINGO
DIGITAL PIR DETECTOR
With
PET IMMUNITY up to 25 kg

SELECT MOUNTING LOCATION

Choose a location most likely to intercept an intruder.
See detection pattern Fig. 1 and Fig. 2.
The BINGO performs best when provided with a
constant and stable environment and background.
The quad-element high quality sensor detects motion
crossing the beam; it is slightly less sensitive detecting
motion toward the detector.
Long Range Curtain Lens - OPTION
When pet immunity is required, optional Long Range
Curtain Lens cannot be used. Pet immunity can only be
achieved with Wide Angle Lens.
AVOID THE FOLLOWING LOCATIONS:
Facing direct sunlight.
Facing areas that may change temperature
rapidly.
Areas where there are air ducts or substantial
airflows.
Avoid screen, curtain that may block detection
area.
Do not install outdoors.

OPENING THE DETECTOR

Cover
Holding
Screw
Fig. 3

PRODUCT FEATURES

The BINGO Detector uses a special designed optical
Lens with unique Quad (Four element) PIR Sensor and
new ASIC based electronics optimized to eliminate false
alarms, caused by small animals and Pets.
The BINGO provides unprecedented levels of immunity
against visible light.
The Detector offers an exceptional level of detection
capability and stability for every security installation.
The BINGO is supplied with Wide Angle lens with PET
immune function.
• Four Element Imaging Technology "Quad".
• ASIC based electronics.
• Immunity to animals up to 25kg (55 lbs).
• 18m Detection Range with Wide Angle Lens.
• Temperature compensation.
• Compact Design for Residential Installation.
• Variable pulse width adjustment.
• Sensitivity adjustment.
• Environmental immunity.
• Height installation calibration free (1.8~2.4m).
• LED ON/OFF Jumper
• Selectable Pulse Count (1, 2 or 3)
• Selectable PET Size (15Kg or 25 Kg)
• EOL – spare Terminals
• Tamper Switch
• Sensitivity Calibration

PET IMMUNITY

Pet immunity is most effective on the following sized
animals:
Rodents = 5 to 12cm high
Cats = 5 to 35 cm high at normal room temperature.
Small to medium sized dogs = 10 to 45cm high at
normal room temperature.
When a dog jumps up on desks, the BINGO may detect
it. Adjust detection area to avoid such places.
Mount between 2.1 and 2.4m. (For better immunity,
especially for medium sized dogs, mount as close to
2.4m, as possible).
Do not angle detector towards the ground or use the
angle bracket.
Mount flat on the wall or in the corner.
For best pet immunity, limit the detectors field of view to
10~12m maximum in any direction.
Pulse Count 2 or 3 is not required for Pet Immunity
applications.
Use 2 or 3 pulse only in harsh environment.
For rodents.
If any shelves within 4.5m of the detector have a height
that comes within 0.5~1m below the mounting height of
the detector and rodents can access these areas, pet
immunity will be reduced. Please select mounting
location of detectors carefully to avoid this situation.
For cats.
If there are cats, any shelves in the detection area will
reduce pet immunity.

MOUNTING DESCRIPTION

Fig. 4
Base
Corner mount
knockout x4
Holding
Screw
Fig. 5
Wiring
knockout
Bracket
Screw
knockout
Mounting
knockout x4
Cover
LED
Indicator
Lens

DETECTION PATTERNS

Fig. 1 - Wide Angle Lens
Fig 2 - Long Range Curtain Lens – OPTION

MOUNTING THE DETECTOR

The detector can either be wall or corner mounted.
If ceiling or special wall mounting is required, use the
optional bracket base. Refer to bracket description.
(See fig. 8)
1. Unscrew the holding screw and gently raise the front
cover (Fig. 3).
2. Carefully unscrew the PCB holding screw located on
the PC board (Fig. 7).
3. Break out the desired knockout holes for proper
installation (Fig. 4).
4. The circular and rectangular indentations at the bottom
base are the knockout holes for wire entry. You may
also use mounting holes that are not in use for running
the wiring into the detector (Fig. 4).
5. For bracket mounting option - lead wire through the
bracket.
6. Mount the detector base to the wall, corner or ceiling.
(For option with bracket see Fig. 8).
7. Reinstall the PC board by fully tightening the holding
screw. Connect wire to terminal block.
8. Replace the cover by inserting it back in the
appropriate closing pins and screw in the holding
screw.

TERMINAL BLOCK CONNECTIONS

Fig. 6
Terminal 1 - Marked - (GND)
Connect to ground of the control panel.
Terminal 2 - Marked + ( +12V )
Connect to the positive Voltage output of 8.2 ~ 16Vdc
source (usually from the alarm control unit).
Terminals 3&6 - Marked EOL
End of line options.
Terminals 4 & 5 - Marked TAMPER
Connect these terminals to a 24hour normally closed
protective zone in the control unit.
Once the front cover of the detector is opened, an
immediate alarm signal will be sent to the control unit.
Terminals 7 & 8 - Marked RELAY
These are the output relay contacts of the detector.
Connect to the control at zone input.