Related Manuals for elero AstroTec-868
Summary of Contents for elero AstroTec-868
- Page 1 AstroTec-868 28 320.0001 AstroTec-868 bidi 28 320.0006 AstroTec-915 bidi 28 320.0906 Operating instructions (translation) Please keep these instructions in a safe place! Timer is preprogrammed 181004506_EN_1114...
-
Page 2: Table Of Contents
Battery replacement ..........43 Programming other AstroTec-868 bidi transmitters ....26 Cleaning . -
Page 3: Safety Instructions
Always observe the following instructions. • For use in dry rooms only. Manual/automatic Warning! sliding switch UP button • Use unmodified elero original parts only. • Keep persons away from the systems guide track. STOP button Transmission • Keep children away from controls. -
Page 4: General Information
(sunrise and sundown). It is to be noted that the range of the radio signal is restricted by legislators and planning regulations. The AstroTec-868/-868 bidi/-915 bidi can be operated manually at any time. The easy-to-install light sensor allows the AstroTec-868/-868 bidi/ -915 bidi to be extended to include a convenient sunshade func- tion (shading plants and furniture). -
Page 5: Initial Operation
Warnhinweise Initial operation Light sensors To activate the AstroTec-868/-868 bidi/-915 bidi timer, touch any Note: If you wish to connect a light sensor to the button on the device. To select the language required use the AstroTec 868/-868 bidi, the instructions provided with +/- buttons and confirm your selection with the OK button. -
Page 6: Explanation Of Functions
Explanation of functions Explanation of functions Warnhinweise +/- buttons Programme The following operations are possible using the + and - buttons: PROGRAMME • Menu → change value The PROGRAMME menu allows you to set various switching • Auto mode → request information times: •... - Page 7 ASTRO WEEK Using the WEEK menu, you can set the same switching times The AstroTec-868/-868 bidi/-915 bidi automatically controls from Monday – Sunday (1-7). your roller shutters or blinds at the pre-set sunrise and sunset times. These times are used as guidelines.
-
Page 8: Switching Time, Offset
Explanation of functions Explanation of functions Warnhinweise SWITCHING TIME SETTING The SETTING menu gives you the following options: Automatic switching times for roller shutters and blinds to be raised and lowered. • HOLIDAY • SUN (when sensor is connected) OFFSET •... -
Page 9: Longitude/Latitude/Time Zone
POSITION, the drive first moves into the lower limit position and daylight saving changes. If the default setting is ON, the then into the ventilation/reverse position according to an automatic AstroTec-868/-868 bidi adjusts itself automatically. control command ▼. 16 | EN... -
Page 10: Expert Mode
Explanation of functions Programming radio channel settings Warnhinweise FUNCTION PRIORITY (factory setting priority = OFF, only visible in expert mode) This mode is intended for qualified electricians only! (Will only appear when the operating device is disconnected) If the priority is switched to “ON“, the clock has a higher priority and The FUNCTION menu gives you the option of setting the following overrides the manual-automatic sliding switch setting of the hand-held functions:... -
Page 11: Program Transmitters/Program End Positions
4. To define the keyboard layout, press the UP button of the 1. Press the following buttons simultaneously: AstroTec-868 (located on the front of the device) as soon as the • Programming button P (on back of device) shutter/blind begins to move upwards (after approx. 1 second). - Page 12 AstroTec-868 bidi AstroTec-868 bidi The AstroTec-868 bidi (item No 28 320.0006) is a radio wall trans- Please press the DOWN button on the AstroTec-868 bidi/-915 bidi mitter for exclusive use with bi-directional receivers (use of directly after the start of a downward movement and the status of the AstroTec-868 bidi with unidirectional transmitters and receiv- the bi-directional teach-in is signaled acoustically.
- Page 13 Delete individual transmitters Programming/deletion of the radio transmitter As long as the AstroTec-868 bidi/-915 bidi has not been programmed for Press the teach-in button P (on the rear side of the device) and the at least one receiver, each press of a button results in an acoustic signal STOP- button (on the front of the device) simultaneously.
-
Page 14: Programming
In order to define the keyboard layout, press the UP button (front 2. To select further menus, press the +/- buttons. of the device) on the AstroTec-868 bidi/-915 bidi immediately 3. Press the MENU button to switch to operating mode. -
Page 15: Programme (Setting Control Commands And Idle Periods)
Programming Programming Warnhinweise PROGRAMME ASTRO WEEK Press +/- for the WEEK menu level (1-7). All further entries now PROG 1/ASTRO WEEK (Astro function for week + idle period ▲▼) refer to every day of the week. PROG 1/ASTRO BLOCK (Astro function for block 1/2 + idle period ▲▼) Confirm by pressing OK. - Page 16 Programming Programming Warnhinweise 4. Confirm by pressing OK. ASTRO EVENING appears. PROGRAMME 5. Confirm by pressing OK. PROG 1/INDIVIDUAL WEEK (Individual switching time ▲▼ for week) PROG 1/INDIVIDUAL BLOCK (Individual switching time ▲▼ for 6. Now select the PROG1 ASTRO function you require using +/- : block1/2) ASTRO EVENING WEEK PROG 1/INDIVIDUAL INDIVIDUAL (Individual switching time ▲▼...
- Page 17 Programming Programming Warnhinweise INDIVIDUAL INDIVIDUAL 8. Now select the PROG 2 INDIVIDUAL function you require Press +/- for the INDIVIDUAL menu level (1,2,3,4,5,6,7). using the +/- buttons: All further entries now refer to every individual day of the week. INDIVIDUAL BLOCK Confirm by pressing OK.
-
Page 18: Prog 2 Offset
Programming Programming Warnhinweise PROGRAMME SETTING PROG 2/OFFSET (e.g. shutters are lowered to ventilation HOLIDAY, LIGHT SENSOR (Holiday OFF/ON, sun/twilight setting) position in the evening) LIGHT SENSOR SETTING HOLIDAY PROGRAMME CONNECTED ? next page +/– PROG 2 HOLIDAY ON +/– OFFSET OFFSET TWILIGHT ▼... - Page 19 Programming Programming Warnhinweise SETTING SETTING INTERMEDIATE POSITION, VENTILATION/REVERSE, PROG 1 PROG 2 END LIMIT (Time/ position programming) END LIMIT (Time/position programming) PROG 2 previous page next page PROG 1 END LIMIT INTERMEDIATE VENTILATION previous page (REVERSE) END LIMIT next page POSITITION +/–...
-
Page 20: English En, Astro Shift
Programming Programming Warnhinweise SETTING 7. You can set the required astro shift ▼ (max. +/- 120 minutes) using the +/- button. ENGLISH EN/ ASTRO SHIFT ▲▼ (Language, astro shift) 8. Confirm by pressing OK. The function ASTRO SHIFT ▼ has now been set. TEST MODE ASTRO previous page... -
Page 21: Time Zone)
Programming Programming Warnhinweise (PRIORITY FOR CLOCK/HAND-HELD TRANSMITTER, SHADING Note: These dialog windows (LONGITUDE, LATITUDE, FUNCTION) TIME ZONE) are only displayed when the EXPERT MODE in the function menu is ON. 3. You can set the degrees LONGITUDE using the +/- button. PRIORITY OFF SHADING OFF SETTING... -
Page 22: Technical Data
Technical data / Battery replacement / Programming Warnhinweise Cleaning FUNCTION (only when the operating device is disconnected, Technical data only for qualified electricians) Nominal voltage 3 V DC ROLLER SHUTTER/BLIND, DRIVE CONTROLLER/ GROUP CONTROLLER, RUNNING TIME Battery type 2 x LR 03 (AAA) (Selection of shutter/blind, selection of the drive controller/group System of protection IP20... -
Page 23: Troubleshooting
GmbH hereby declares that the AstroTec 868 / 4. Astro shift is set. 4. Adjust astro shift. AstroTec-868 bidi / AstroTec-915 bidi complies with the basic prerequisites and the other relevant provisions of the EC direc- The AstroTec-868 The sliding switch Move the sliding tives. - Page 24 46 | EN EN | 47...
- Page 25 GmbH Antriebstechnik Linsenhofer Str. 65 72660 Beuren info@elero.de www.elero.com 309058 01...
Need help?
Do you have a question about the AstroTec-868 and is the answer not in the manual?
Questions and answers