Mitsubishi Electric GT1030-HBD General Description page 3

JY997D25301T
Side
JAPANESE
A
Side
ENGLISH
B
GT1030-HD(W)/HD(W)2/HL(W)
GT10 General Description
Manual Number JY997D25301T
Date Oct. 2016
This manual describes the specifications of the product. Before use, read this
manual and manuals of relevant products fully to acquire proficiency in handling
and operating the product. Make sure to learn all the product information, safety
information, and precautions.
And, store this manual in a safe place so that you can take it out and read it
whenever necessary. Always forward it to the end user.
Registration
The company name and the product name to be described in this manual are the
registered trademarks or trademarks of each company.
Effective Oct. 2016
Specifications are subject to change without notice.

2008 MITSUBISHI ELECTRIC CORPORATION
Safety Precaution
(Read these precautions before using.)
Before using this product, please read this manual and the relevant manuals introduced
in this manual carefully and pay full attention to safety to handle the product correctly.
The precautions given in this manual are concerned with this product.
In this manual, the safety precautions are ranked as "WARNING" and
"CAUTION".
Indicates that incorrect handling may cause hazardous
conditions, resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous
conditions, resulting in medium or slight personal injury
or physical damage.
Depending on circumstances, procedures indicated by "CAUTION" may also be
linked to serious results.
In any case, it is important to follow the directions for usage.
DESIGN PRECAUTIONS
 Some failures of the GOT or cable may keep the outputs on or off.
An external monitoring circuit should be provided to check for output signals
which may lead to a serious accident.
Not doing so can cause an accident due to false output or malfunction.
 If a communication fault (including cable disconnection) occurs during
monitoring on the GOT, communication between the GOT and PLC CPU is
suspended and the GOT becomes inoperative.
A system where the GOT is used should be configured to perform any
significant operation to the system by using the switches of a device other
than the GOT on the assumption that a GOT communication fault will occur.
Not doing so can cause an accident due to false output or malfunction.
 Do not use the GOT as the warning device that may cause a serious accident.
An independent and redundant hardware or mechanical interlock is required to
configure the device that displays and outputs serious warning.
Failure to observe this instruction may result in an accident due to incorrect
output or malfunction.
 Incorrect operation of the touch switch(s) may lead to a serious accident if the
GOT backlight is gone out. When the GOT backlight goes out, causes the
monitor screen to appear blank, while the input of the touch switch(s) remains
active. This may confuse an operator in thinking that the GOT is in
"screensaver" mode, who then tries to release the GOT from this mode by
touching the display section, which may cause a touch switch to operate.
DESIGN PRECAUTIONS
 Do not bundle the control and communication cables with main-circuit, power
or other wiring.
Run the above cables separately from such wiring and keep them a minimum
of 100mm (3.94in.) apart.Not doing so noise can cause a malfunction.
 Do not press the GOT display section with a pointed material as a pen or
driver. Doing so can result in a damage or failure of the display section.
 Before connecting to GOT, turn ON the controller to enable the
communication. When the communication of controller is not available, a
communication error may occur in GOT.
1. Specifications
1.1 General Specifications
Specifications
Item
GT1030-HD/HD2/HL/HDW/HDW2/HLW
Display
0 to 50C
Operating
section
ambient
Other than
tempera-
0 to 55C (When mounted horizontally), 0 to 50C (When
display
ture
mounted vertically)
section
Storage ambient
-20 to 60C
temperature
Operating/Storage 10 to 90% RH, non-condensing (The wet bulb temperature
ambient humidity is 39C or less.)
Half-
Fre- Acceler-
ampli-
quency ation
tude
Con-
5 to
U n d e r
forms -- 3.5mm
8.4Hz
intermit-
to JIS
t e n t
Vibration resistance B3502 8.4 to
9.8m/s 2
vibration
and 150Hz
IEC61131
5 to
U n d e r
-2 -- 1.75mm
8.4Hz
c o n t i n u -
o u s
8.4 to
4.9m/s 2
vibration
150Hz
Conforms to JIS B3502, IEC 61131-2 (147m/s
Shock resistance
half-wave pulse, 3 times each in the X, Y, and Z directions.)
Must be free of lamp black, corrosive gas, flammable gas,
Operating atmosphere or excessive amount of electro conductive dust particles
and must be no direct sunlight. (Same as for saving)
*1
Operating altitude 2000 m (6562 ft) max.
Installation location Inside control panel
Overvoltage
II or less
category *2
Pollution degree *3 2 or less
Cooling method Self-cooling
*1 Do not use or store the GOT under pressure higher than the atmospheric
pressure of altitude 0m (0ft.). Failure to observe this instruction may cause a
malfunction.
When the air inside the control panel is purged by pressurization, the surface
sheet may be lifted by high pressure. As a result, the touch panel may be
difficult to press, and the sheet may be peeled off.
*2 This indicates the section of the power supply to which the equipment is
assumed to be connected between the public electrical power distribution
network and the machinery within the premises.
Category II applies to equipment for which electrical power is supplied from
fixed facilities.
The surge voltage withstand level for up to the raged voltage of 300 V is 2500 V.
*3 This index indicates the degree to which conductive material is generated in
the environment where the equipment is used.
In pollution degree 2, only non-conductive pollution occurs but temporary
conductivity may be produced due to condensation.
1.2 Performance Specifications
Specifications
GT1030-
Item
GT1030- GT1030-
HDW/
HD/HD2 HL
HDW2
Type STN monochrome (white/black) liquid crystal
Screen size 4.5"
Display
section * 288  96 dots (Horizontal format)
Resolution
1
W109.42(4.3)  H35.98(1.41) [mm](inch) (Horizontal
Display size
format)
16-dot standard font: 36 characters  6 lines, 12-dot
D i s p l a y
character standard font: 48 characters  8 lines (Horizontal format)
Display color Monochrome (white/black)
Left/Right: 30 degrees, Top: 20 degrees, Bottom: 30
Display angle
degrees (Horizontal format)
Display C o n t r a s t
16-level adjustment
adjustment
section *
1
I n t e n s i t y o f
2 2
200 [cd/m ] (in green) 500 [cd/m ] (in white)
LCD only
I n t e n s i t y
8-level adjustment
adjustment
Approx. 50,000h. (Time for display intensity to become 1/5
Life
at operating ambient temperature of 25C)
LED with 3 available colors LED with 3 available colors
(green, red, orange) (white, red, pink)
Backlight (no
B ac k li g ht stat us (c o lo rs , O N / B LI N K / OF F) c o nt ro l,
replacement required)
Adjustable screensaver activation time
Setting the system information enables *2 PLC to control the
backlight status
Side
B
MOUNTING PRECAUTIONS
 Be sure to shut off all phases of the external power supply used by the system
before mounting or removing the GOT to/from the panel.
Not doing so can cause the unit to fail or malfunction.
 When installing the battery wear an earth band etc. to avoid the static electricity.
The static electricity can cause the unit to fail or malfunction.
MOUNTING PRECAUTIONS
 Use the GOT in the environment that satisfies the general specifications
described in this manual. Not doing so can cause an electric shock, fire,
malfunction or product damage or deterioration.
 When mounting the GOT to the control panel, tighten the mounting screws in the
specified torque range. Undertightening can cause the GOT to drop, short circuit
or malfunction, and deteriorate the waterproof effect and oilproof effect.
Overtightening can cause a drop, short circuit or malfunction due to the damage
of the screws or the GOT, and deteriorate the waterproof effect and oilproof effect
due to distortion of the protective cover for oil, GOT or panel.
 When using the GOT in the environment of oil or chemicals, use the protective
cover for oil. Failure to do so may cause failure or malfunction due to the oil or
chemical entering into the GOT.
WIRING PRECAUTIONS
 Be sure to shut off all phases of the external power supply used by the system
before wiring. Failure to do so may result in an electric shock, product damage or
malfunctions.
 Please make sure to ground FG terminal of the GOT power supply section by
applying 100 or less which is used exclusively for the GOT. Not doing so may
cause an electric shock or malfunction.
 Correctly wire the GOT power supply section after confirming the rated voltage
and terminal arrangement of the product. Not doing so can cause a fire or failure.
 Tighten the terminal screws of the GOT power supply section in the specified
torque range. Undertightening can cause a short circuit or malfunction.
Overtightening can cause a short circuit or malfunction due to the damage of the
screws or the GOT.
 Exercise care to avoid foreign matter such as chips and wire offcuts entering the
GOT. Not doing so can cause a fire, failure or malfunction.
WIRING PRECAUTIONS
 Plug the communication cable into the connector of the connected unit and
tighten the mounting and terminal screws in the specified torque range.
Undertightening can cause a short circuit or malfunction. Overtightening can
cause a short circuit or malfunction due to the damage of the screws or unit.
TEST OPERATION
PRECAUTIONS
 Before performing the test operations of the user creation monitor screen (such as
turning ON or OFF bit device, changing the word device current value, changing
the settings or current values of the timer or counter), read through the manual
carefully and make yourself familiar with the operation method.
During test operation, never change the data of the devices which are used to
perform significant operation for the system. False output or malfunction can
cause an accident.
STARTUP/MAINTENANCE
PRECAUTIONS
 When power is on, do not touch the terminals.
Doing so can cause an electric shock or malfunction.
 Connect the battery correctly. Do not discharge, disassemble, heat, short, solder or
throw the battery into the fire. Incorrect handling may cause the battery to
generate heat, burst or take fire, resulting in injuries or fires.
 Before starting cleaning or terminal screw retightening, always switch off the
power externally in all phases. Not switching the power off in all phases can cause
a unit failure or malfunction. Undertightening can cause a short circuit or
malfunction. Overtightening can cause a short circuit or malfunction due to the
damage of the screws or unit.
STARTUP/MAINTENANCE
PRECAUTIONS
 Do not disassemble or modify the unit.
Doing so can cause a failure, malfunction, injury or fire.
 Do not touch the conductive and electronic parts of the unit directly.
Doing so can cause a unit malfunction or failure.
 The cables connected to the unit must be run in ducts or clamped.
Not doing so can cause the unit or cable to be damaged due to the dangling,
motion or accidental pulling of the cables or can cause a malfunction due to a
cable connection fault.
 When unplugging the cable connected to the unit, do not hold and pull the cable
portion. Doing so can cause the unit or cable to be damaged or can cause a
malfunction due to a cable connection fault.
Specifications
Item
GT1030- GT1030-
HD/HD2 HL
N u m b e r o f
Maximum 50 keys/screen (Matrix resistive film touch panel)
touch keys
Minimum 16  16 dots (per key)
Key size
Simultaneous
Touch
p r e s s i n g o f
panel
two (or
Enable
more) areas
( 2 - p o i n t
press)
Life 1 million times or more (operating force 0.98N max.)
Flash memory ROM (Internal), for storing Project data
Sweep C drive *3
(1.5M bytes or less), OS
Count
L i f e
Memory (Number of 100,000 times
write times)
10 times
SRAM (Internal), for storing alarm history, recipe data and
each in
-- D drive
time action setting value
X, Y
and Z
GT11-50BAT lithium battery
direc-
Type Magnesium maganese dioxide lithium primary battery
tions
Battery
-- Backup
Clock data, alarm history and recipe data
target
2 , 11 ms, Sine
Life Approx. 5 years (Operating ambient temperature of 25)
Buzzer output
(a buzzer that sounds
Single tone (LONG/ SHORT/ OFF adjustable)
when touch keys are
pressed)
E n v i r o n m e n t a l
Equivalent to IP67 (JEM1030) (front section)
protective structure *4
W145(5.7)  H76(2.99)  D29.5(1.16)[mm](inch) (Excluding
External dimensions
mounting fixtures) (Horizontal format)
Panel cutting
W137(5.39)  H66(2.59) [mm](inch) (Horizontal format)
dimensions
Weight (Excluding
0.3kg 0.28kg
mounting fixtures)
Compatible software
GT Designer3 Version1.19V or later
package
*1  Bright dots (always lit) and dark dots (unlit) may appear on a liquid crystal
display panel. It is impossible to completely avoid this symptom, as the liquid
crystal display comprises of a great number of display elements. Flickers may
be observed depending on the display color.
Please note that these dots appear due to its characteristic and are not
caused by product defect.
 Flickers and partial discoloration may be generated on the liquid crystal
display panel due to the display contents or the contrast adjustment.
However, please note that these phenomena appear due to its characteristic
and are not caused by product defect.
 There is a difference in the display brightness and the color tones between
liquid crystal display panels. When using multiple liquid crystal display panels,
please note that there is an individual difference between them.
 A crosstalk (shadow as an extension of the display) may appear on the liquid
crystal display panel. Please note that it appears due to its characteristic.
 When the display section is seen from the outside of the display angle, the
display color seems like it has changed.
GT1030-
Please note that it is due to its characteristic. Please note that the response
HLW
time, brightness and color of the liquid crystal display panel may vary
depending on the usage environmental temperature.
Especially in the low temperature environment, the display response
becomes slow due to the characteristics of the STN liquid crystal.
Please check the display response in advance for using this product.
 Please note that the response in low temperatures tend to be slower as a
characteristic of the liquid crystal display panel.
 When the same screen is displayed for a long time, an incidental color or
partial discoloration is generated on the screen due to heat damage, and it
may not disappear.
To prevent heat damage, the screen saver function is effective.
For details of the screen saver function, refer to the following.
 GT10 User's Manual
*2 For the details of system information, refer to the following.
 GT Designer3 Version1 Screen Design Manual
*3 ROM in which new data can be written without deleting the written data.
*4 Note that this does not guarantee all users' operation environment.
In addition, the product may not be used in environments under exposition of
oil or chemicals for a long period of time, or in environments filled with oil-mist.
1.3 Communication Specifications
Item
GT1030-
HD/HDW
Communication R S - 4 2 2 / 4 8 5
standard 1ch
PLC Tr a n s m i s s i o n
115,200/57,600/38,400/19,200/9,600/4,800bps
communication speed
C o n n e c t o r
Connector terminal block 9-pins
shape
STARTUP/MAINTENANCE
PRECAUTIONS
 Do not drop or apply any impact to the battery.
If any impact has been applied, discard the battery and never use it.
The battery may be damaged by the drop or impact.
 Before touching the unit, always touch grounded metal, etc. to discharge static
electricity from human body, etc.
Not doing so can cause the unit to fail malfunction.
 Replace battery with GT11-50BAT by Mitsubishi electric Co. only.
Use of another battery may present a risk of fire or explosion.
 Dispose of used battery promptly.
Keep away from children. Do not disassemble and do not dispose of in fire.
DISPOSAL PRECAUTIONS
 When disposing of the product, handle it as industrial waste.
 When disposing of batteries, separate them from other wastes according to the
local regulations. (For details of the battery directive in EU member states, refer
GOT User's Manual.)
TRANSPORTATION
PRECAUTIONS
 When transporting lithium batteries, make sure to treat them based on the
transport regulations. (Refer to User's Manual for details of the regurated
models.)
 Before transporting the GOT, turn the GOT power on and check that the battery
voltage status is normal on the Time setting & display screen (utilities screen). In
addition, confirm that the adequate battery life remains on the rating plate.
Transporting the GOT with the low battery voltage or the battery the reached
battery life may unstabilize the backup data unstable during transportation.
 Make sure to transport the GOT main unit and/or relevant unit(s) in the manner
they will not be exposed to the impact exceeding the impact resistance
described in the general specifications of this manual, as they are precision
devices. Failure to do so may cause the unit to fail.
Check if the unit operates correctly after transportation.
Compliance with EC directive (CE Marking)
This note does not guarantee that an entire mechanical module produced in
accordance with the contents of this note will comply with the following standards.
Compliance to EMC directive for the entire mechanical module should be checked by
the user / manufacturer. For more details please contact the local Mitsubishi Electric
sales site.
Attention
 This product is designed for use in industrial applications.
Requirement for Compliance with EMC directive
The following products have shown compliance through direct testing (to the
identified standards) and design analysis (forming a technical construction file) to the
European Directive for Electromagnetic Compatibility (2004/108/EC) when used as
directed by the appropriate documentation.
Type :Programmable Controller (Open Type Equipment)
Standard
EMI
EN61131-2 : 2007
Programmable
controllers- Equipment,
EMS
requirement and tests
For more details please contact the local Mitsubishi Electric sales site.
Notes for compliance to EMC regulation
1) General notes on the use of communication cables
Any device which utilizes a data communication function is susceptible to the
wider effects of local EMC noise. Therefore, when installing any communication
cables care should always be taken with the routing and location of those cables.
The GOT units identified on the previous chapter are compliant with the EMC
requirement when the following communication cables are used.
GOT Unit
GT1030-HBD/HWD/HBL/HWL/HBDW/HWDW/
HBLW/HWLW
GT1030-HBD2/HWD2/HBDW2/HWDW2
2) General notes on the use of the power cable
The GT1030-HD/HD2/HDW/HDW2 unit demand that the cable for the
power supply is 10m or less.
Item
GT1030-
GT1030-
HDW/
HLW
HDW2
Te r m i n a t i n g
PLC
communication *1
resistor
Communication
standard
PC
Tr a n s m i s s i o n
c o m m u n i c a -
speed
*2
tion
C o n n e c t o r
shape
*1 Set the terminating resistor selector switch of the GOT in accordance with the
connection type when adopting GOT multidrop connection.
For details of GOT multidrop connection, refer to the following.
GOT1000 Series Connection Manual (Mitsubishi Products) for GT Works3
*2 Project data upload/download, OS installation, Transparent function
1.4 Power Supply Specifications
(For details on power supply wiring, such as the allowable cable size and tightening
torque, refer to the additional manual, "GT10 User's Manual".)
Item
GT1030-HD/HD2/HDW/
Input power supply 24VDC (+10% -15%),
voltage ripple voltage 200mV or less
F u s e ( b u i l t - i n , n o t
0.5A
exchangeable)
Power consumption, 2.2W (90mA/24VDC) or less,
(At backlight off) (1.7W (70mA/24VDC) or less)
Inrush current 18A or less (26.4VDC) 1ms
P e r m i s s i b l e
0.3kg 0.28kg
instantaneous power Within 5ms
failure time *1
Noise voltage: 1000Vp-p, Noise width: 1s (by noise
Noise immunity
simulator of 30 to 100Hz noise frequency)
5 0 0 VA C
Dielectric withstand (between the GOT's power
voltage s u p p l y t e r m i n a l s a n d t h e
GOT's grounding terminal)
10M or larger by insulation
resistance tester (between the
Insulation resistance GOT's power supply terminals
and the G OT's ground ing
terminal)
G ro u n d i n g w i t h a g r o u n d
resistance of 100 Ω or less by
using a ground cable that has
a cross-sectional area of 0.14
to 1.5 mm
Grounding to 1.0 mm
0.25 to 0.5 mm
with an insulation sleeve).
If impossible, connect the
ground cable to the control
panel.
*1 The GOT continues to operate even upon 5ms or shorter instantaneous
power failure. The GOT stops operating if there is extended power failure or
voltage drop, while it automatically resumes operation as soon as the power is
restored.
2. Wiring of connection cable
The diagram below shows cable assignment for GOT port.
Cables: GT10-CR4-8P, GT10-CR4-2P, GT10-CR2-6P
GOT
PLC connection cable
GT10-C R4-8P
GOT
Untied
(terminal
wire
Specifications
block)
color
24V 5V
GT1030- GT1030-
SDA Brown
HD2/HDW2 HL/HLW
Red
SDB
Orange
RDA
RS-232 1ch RS-422 1ch
RDB Yellow
Green
SG
RSA Black
RSB White
CSA -
+
CSB
Associated Manuals
The following manuals are relevant to this product. When these loose manuals are
required, please consult with our local distributor.
Manual name
GT10 User's Manual
(sold separately)
GT Designer3 Version1
Screen Design Manual
(For GOT1000 Series)
(Fundamentals)1/2, 2/2
(sold separately)
GT Designer3 Version1
Screen Design Manual
(For GOT1000 Series)
(Functions) 1/2, 2/2
(sold separately)
GOT1000 Series
Connection Manual
(Mitsubishi Products)
for GT Works3
(sold separately)
*1 Stored in the GT Works3/GT Designer3 in PDF format.
For details of a PLC to be connected, refer to the PLC user's manual respectively.
Bundled Items
GT1030-HBD/HWD
GT1030-HBD2/HWD2
GT1030-HBL/HWL
GT1030-HBDW/HWDW
GT1030-HBDW2/HWDW2
GT1030-HBLW/HWLW
PLC Communication Connector
Panel Mounting Bracket (with M4  20 screws)
Panel Mounting Packing
GT10 General Description (This manual)
Explanation of the GOT model name
Remark
GT10 3 0 -
Compliance with all relevant aspects of the
standard. (Radiated Emissions)
Compliance with all relevant aspects of the
standard. (ESD,RF electromagnetic field, EFTB,
Surge, RF conducted disturbances and Power
frequency magnetic field)
Existing Cables
GT10-C30R4-8P
(For Melsec FX series PLC)
GT10-C30R2-6P
(For Melsec Q series PLC)
User-made cable is necessary, depending on the PLC.
Specifications
For the detail, refer to GOT1000 Series Connection Manual (Mitsubishi Products) for
GT1030- GT1030- GT1030-
GT Works3.
HD/HDW HD2/HDW2 HL/HLW
O p e n / 11 0  /
330 (Switched
by
Recommended Tool (Screwdriver)
t e r m i n a t i n g
resistor selector -- --
switch)
(At factory
s h i p m e n t : 「电器电子产品有害物质限制使用标识要求」 的表示方式
330)
RS-232 1ch
115,200/57,600/38,400/19,200/9,600/4,800bps
含有有害6物质的名称， 含有量， 含有部品
MINI DIN 6-pins (Female)
本产品中所含有的有害 6 物质的名称， 含有量， 含有部品如下表所
示。
部件名称
Specifications
GT1030-HL/HLW
HDW2
5VDC (5%),
显 示 器
supplied from the PLC
GOT
--
1 . 1 W ( 2 2 0 m A / 5 V D C ) o r
less, (0.6W (120mA/5VDC)
or less)
本表格依据SJ/T 11364的规定编制。
--
○:表示该有害物质在该部件所有均质材料中的含量均在GB/T 26572
--
规定的限量要求以下。
×:表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T
26572规定的限量要求。
f o r 1 m i n u t e
--
--
2
(solid wire), 0.14
2 This manual confers no industrial property rights or any rights of any other
(stranded wire), or --
kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation
2
(rod terminal
cannot be held responsible for any problems involving industrial property rights
which may occur as a result of using the contents noted in this manual.
Warranty
Exclusion of loss in opportunity and secondary loss from warranty liability
Regardless of the gratis warranty term, Mitsubishi shall not be liable for
compensation to:
(1) Damages caused by any cause found not to be the responsibility of
Mitsubishi.
(2) Loss in opportunity, lost profits incurred to the user by Failures of Mitsubishi
products.
(3) Special damages and secondary damages whether foreseeable or not,
compensation for accidents, and compensation for damages to products
other than Mitsubishi products.
PLC (4) Replacement by the user, maintenance of on-site equipment, start-up test run
and other tasks.

This product has been manufactured as a general-purpose part for general
GT10-C R4-25P GT10-C R2-6P
industries, and has not been designed or manufactured to be incorporated in
GOT
GOT
Untied Untied
(terminal (terminal
a device or system used in purposes related to human life.
wire wire
block) block)
color color  Before using the product for special purposes such as nuclear power, electric
24V 24V
power, aerospace, medicine or passenger movement vehicles, consult with
SDA Brown SD Brown
Mitsubishi Electric.
SDB Red RD Red

This product has been manufactured under strict quality control. However
Orange ER Blue
RDA
when installing the product where major accidents or losses could occur if the
RDB Yellow DR Yellow
product fails, install appropriate backup or failsafe functions in the system.
SG Green SG Green
Blue RS Purple
RSA
RSB Purple CS
CSA Black NC
White NC
CSB
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
Manual Number
Contents
(Model Code)
Describes the GT10 hardware-
r e l e v a n t c o n t e n t s u c h a s pa r t
n a m e s , e x t e r n a l d i m e n s i o n s , JY997D24701
mounting, power supply wiring, (09R819)
specifications, and introduction to
option devices
D e s c r i b e s m e t h o d s o f t h e G T
Designer3 installation operation, SH-080866ENG
basic operation for drawing and (1D7MB9)
transmitting data to GOT1000 series
*1
D e s c r i b e s s p e c i f i c a t i o n s a n d
SH-080867ENG
settings of the object functions used
(1D7MC1)
in GT Designer3
*1
Describes system configurations of
the connection method applicable to SH-080868ENG
GOT1000 series and cable creation (1D7MC2)
method
*1
Model Name Remark
GOT main unit
(The maintenance supplies below
are packed with the product.)
Maintenance Supplies Quantity
1
4
1
1
* * * * *
Interface type for 2:RS-232
communication with PLC Blank:RS-422
Backlight type
W:white/red/pink
Blank:green/red/orange
Power type
D:24VDC
L:5VDC
Panel color type B:Black
W:White
Display device type H:STN monochrome(High contrast)
Display color type 0:Monochrome(black/white)
Screen size type 3:4.5"
GOT1000 series GT10
Cable jacket to remove 7mm (0.27")
Tightening torque 0.22 to 0.25 N m

SZS 0.4  2.5 (Phoenix Contact Inc.)
Note: This symbol mark is for China only.
产品中有害物质的名称及含量
有害物质
多溴
铅 汞 镉 六价铬 多溴联苯
二苯醚
(Pb) (Hg) (Cd) (Cr(VI)) (PBB)
(PBDE)
外壳 ○ ○ ○ ○ ○
印刷基板 × ○ ○ ○ ○
背光灯
○ × ○ ○ ○
(CCFL)
电缆 × ○ ○ ○ ○
For safe use
○
○
○
○