Mitsubishi Electric GT1030-HBD General Description page 2

1. Specifications
1.1 General Specifications
Specifications
Item
GT1030-HD/HD2/HL/HDW/HDW2/HLW
Display
0 to 50C
Operating
section
ambient
Other than
tempera-
0 to 55C (When mounted horizontally), 0 to 50C (When
display
ture
mounted vertically)
section
Storage ambient
-20 to 60C
temperature
Operating/Storage 10 to 90% RH, non-condensing (The wet bulb temperature
ambient humidity is 39C or less.)
Half-
Fre- Acceler-
ampli-
quency ation
tude
Con-
5 to
U n d e r
forms -- 3.5mm
8.4Hz
intermit-
to JIS
t e n t
Vibration resistance B3502 8.4 to
9.8m/s 2 --
vibration
and 150Hz
IEC61131
5 to
U n d e r
-2 -- 1.75mm
8.4Hz
c o n t i n u -
o u s
8.4 to
4.9m/s 2 --
vibration
150Hz
Conforms to JIS B3502, IEC 61131-2 (147m/s
Shock resistance
half-wave pulse, 3 times each in the X, Y, and Z directions.)
Must be free of lamp black, corrosive gas, flammable gas,
Operating atmosphere or excessive amount of electro conductive dust particles
and must be no direct sunlight. (Same as for saving)
*1 2000 m (6562 ft) max.
Operating altitude
Installation location Inside control panel
Overvoltage
II or less
category *2
Pollution degree *3 2 or less
Cooling method Self-cooling
*1 Do not use or store the GOT under pressure higher than the atmospheric
pressure of altitude 0m (0ft.). Failure to observe this instruction may cause a
malfunction.
When the air inside the control panel is purged by pressurization, the surface
sheet may be lifted by high pressure. As a result, the touch panel may be
difficult to press, and the sheet may be peeled off.
*2 This indicates the section of the power supply to which the equipment is
assumed to be connected between the public electrical power distribution
network and the machinery within the premises.
Category II applies to equipment for which electrical power is supplied from
fixed facilities.
The surge voltage withstand level for up to the raged voltage of 300 V is 2500 V.
*3 This index indicates the degree to which conductive material is generated in
the environment where the equipment is used.
In pollution degree 2, only non-conductive pollution occurs but temporary
conductivity may be produced due to condensation.
1.2 Performance Specifications
Specifications
GT1030-
Item
GT1030- GT1030-
HDW/
HD/HD2 HL
HDW2
Type STN monochrome (white/black) liquid crystal
Screen size 4.5"
Display
section * 288  96 dots (Horizontal format)
Resolution
1
W109.42(4.3)  H35.98(1.41) [mm](inch) (Horizontal
Display size
format)
D i s p l a y 16-dot standard font: 36 characters  6 lines, 12-dot
character standard font: 48 characters  8 lines (Horizontal format)
Display color Monochrome (white/black)
Left/Right: 30 degrees, Top: 20 degrees, Bottom: 30
Display angle
degrees (Horizontal format)
Display C o n t r a s t
16-level adjustment
* adjustment
section
1
I n t e n s i t y o f
2 2
200 [cd/m ] (in green) 500 [cd/m ] (in white)
LCD only
I n t e n s i t y
8-level adjustment
adjustment
Approx. 50,000h. (Time for display intensity to become 1/5
Life
at operating ambient temperature of 25C)
LED with 3 available colors LED with 3 available colors
(green, red, orange) (white, red, pink)
Backlight (no
B ac k li g ht stat us (c o lo rs , O N / B LI N K / OF F) c o nt ro l,
replacement required)
Adjustable screensaver activation time
Setting the system information enables *2 PLC to control the
backlight status
Specifications
Item
GT1030- GT1030-
HD/HD2 HL
N u m b e r o f
Maximum 50 keys/screen (Matrix resistive film touch panel)
touch keys
Key size Minimum 16  16 dots (per key)
Simultaneous
Touch
p r e s s i n g o f
panel
two (or
Enable
more) areas
( 2 - p o i n t
press)
Life 1 million times or more (operating force 0.98N max.)
Flash memory ROM (Internal), for storing Project data
Sweep C drive *3
(1.5M bytes or less), OS
Count
L i f e
Memory (Number of 100,000 times
write times)
10 times
SRAM (Internal), for storing alarm history, recipe data and
each in
D drive
time action setting value
X, Y
and Z
GT11-50BAT lithium battery
direc-
Type Magnesium maganese dioxide lithium primary battery
tions
Battery
Backup
Clock data, alarm history and recipe data
target
2 , 11 ms, Sine
Life Approx. 5 years (Operating ambient temperature of 25)
Buzzer output
(a buzzer that sounds
Single tone (LONG/ SHORT/ OFF adjustable)
when touch keys are
pressed)
E n v i r o n m e n t a l
Equivalent to IP67 (JEM1030) (front section)
*4
protective structure
W145(5.7)  H76(2.99)  D29.5(1.16)[mm](inch) (Excluding
External dimensions
mounting fixtures) (Horizontal format)
Panel cutting
W137(5.39)  H66(2.59) [mm](inch) (Horizontal format)
dimensions
Weight (Excluding
0.3kg 0.28kg
mounting fixtures)
Compatible software
GT Designer3 Version1.19V or later
package
*1  Bright dots (always lit) and dark dots (unlit) may appear on a liquid crystal
display panel. It is impossible to completely avoid this symptom, as the liquid
crystal display comprises of a great number of display elements. Flickers may
be observed depending on the display color.
Please note that these dots appear due to its characteristic and are not
caused by product defect.
 Flickers and partial discoloration may be generated on the liquid crystal
display panel due to the display contents or the contrast adjustment.
However, please note that these phenomena appear due to its characteristic
and are not caused by product defect.
 There is a difference in the display brightness and the color tones between
liquid crystal display panels. When using multiple liquid crystal display panels,
please note that there is an individual difference between them.
 A crosstalk (shadow as an extension of the display) may appear on the liquid
crystal display panel. Please note that it appears due to its characteristic.
 When the display section is seen from the outside of the display angle, the
display color seems like it has changed.
GT1030-
Please note that it is due to its characteristic. Please note that the response
HLW
time, brightness and color of the liquid crystal display panel may vary
depending on the usage environmental temperature.
Especially in the low temperature environment, the display response
becomes slow due to the characteristics of the STN liquid crystal.
Please check the display response in advance for using this product.
 Please note that the response in low temperatures tend to be slower as a
characteristic of the liquid crystal display panel.
 When the same screen is displayed for a long time, an incidental color or
partial discoloration is generated on the screen due to heat damage, and it
may not disappear.
To prevent heat damage, the screen saver function is effective.
For details of the screen saver function, refer to the following.
 GT10 User's Manual
*2 For the details of system information, refer to the following.
 GT Designer3 Version1 Screen Design Manual
*3 ROM in which new data can be written without deleting the written data.
*4 Note that this does not guarantee all users' operation environment.
In addition, the product may not be used in environments under exposition of
oil or chemicals for a long period of time, or in environments filled with oil-mist.
1.3 Communication Specifications
Item
GT1030-
HD/HDW
Communication R S - 4 2 2 / 4 8 5
standard 1ch
PLC Tr a n s m i s s i o n
115,200/57,600/38,400/19,200/9,600/4,800bps
communication speed
C o n n e c t o r
Connector terminal block 9-pins
shape
Item
GT1030-
GT1030-
HDW/
HLW
HDW2
Te r m i n a t i n g
PLC
communication *1
resistor
Communication
standard
PC
Tr a n s m i s s i o n
c o m m u n i c a -
speed
*2
tion
C o n n e c t o r
shape
*1 Set the terminating resistor selector switch of the GOT in accordance with the
connection type when adopting GOT multidrop connection.
For details of GOT multidrop connection, refer to the following.
GOT1000 Series Connection Manual (Mitsubishi Products) for GT Works3
*2 Project data upload/download, OS installation, Transparent function
1.4 Power Supply Specifications
(For details on power supply wiring, such as the allowable cable size and tightening
torque, refer to the additional manual, "GT10 User's Manual".)
Item
GT1030-HD/HD2/HDW/
Input power supply 24VDC (+10% -15%),
voltage ripple voltage 200mV or less
F u s e ( b u i l t - i n , n o t
0.5A
exchangeable)
Power consumption, 2.2W (90mA/24VDC) or less,
(At backlight off) (1.7W (70mA/24VDC) or less)
Inrush current 18A or less (26.4VDC) 1ms
P e r m i s s i b l e
0.3kg 0.28kg
instantaneous power
Within 5ms
failure time *1
Noise voltage: 1000Vp-p, Noise width: 1s (by noise
Noise immunity
simulator of 30 to 100Hz noise frequency)
5 0 0 VA C
Dielectric withstand (between the GOT's power
voltage s u p p l y t e r m i n a l s a n d t h e
GOT's grounding terminal)
10M or larger by insulation
resistance tester (between the
Insulation resistance GOT's power supply terminals
and the G OT's ground ing
terminal)
G ro u n d i n g w i t h a g r o u n d
resistance of 100 Ω or less by
using a ground cable that has
a cross-sectional area of 0.14
to 1.5 mm
Grounding
to 1.0 mm
0.25 to 0.5 mm
with an insulation sleeve).
If impossible, connect the
ground cable to the control
panel.
*1 The GOT continues to operate even upon 5ms or shorter instantaneous
power failure. The GOT stops operating if there is extended power failure or
voltage drop, while it automatically resumes operation as soon as the power is
restored.
2. Wiring of connection cable
The diagram below shows cable assignment for GOT port.
Cables: GT10-CR4-8P, GT10-CR4-2P, GT10-CR2-6P
GOT
PLC connection cable
GT10-C R4-8P GT10-C
GOT
Untied
(terminal
wire
Specifications
block)
color
GT1030- GT1030- 24V 5V
Brown
HD2/HDW2 HL/HLW SDA
Red
SDB
RDA Orange
RS-232 1ch RS-422 1ch
Yellow
RDB
Green
SG
Black
RSA
RSB White
CSA
-
CSB +
User-made cable is necessary, depending on the PLC.
Specifications
For the detail, refer to GOT1000 Series Connection Manual (Mitsubishi Products) for
GT1030- GT1030- GT1030-
GT Works3.
HD/HDW HD2/HDW2 HL/HLW
Cable jacket to remove
O p e n / 11 0  /
330 (Switched
by
Recommended Tool (Screwdriver)
t e r m i n a t i n g
resistor selector -- --
switch)
(At factory
「电器电子产品有害物质限制使用标识要求」 的表示方式
s h i p m e n t :
330)
RS-232 1ch
115,200/57,600/38,400/19,200/9,600/4,800bps
含有有害6物质的名称， 含有量， 含有部品
MINI DIN 6-pins (Female)
本产品中所含有的有害 6 物质的名称， 含有量， 含有部品如下表所
示。
部件名称
Specifications
GT1030-HL/HLW
HDW2
5VDC (5%),
supplied from the PLC 显 示 器
GOT
--
1 . 1 W ( 2 2 0 m A / 5 V D C ) o r
less, (0.6W (120mA/5VDC)
or less)
本表格依据SJ/T 11364的规定编制。
--
○:表示该有害物质在该部件所有均质材料中的含量均在GB/T 26572
--
规定的限量要求以下。
×:表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T
26572规定的限量要求。
f o r 1 m i n u t e
--
--
2
(solid wire), 0.14
2 -- This manual confers no industrial property rights or any rights of any other
(stranded wire), or
kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation
2
(rod terminal
cannot be held responsible for any problems involving industrial property rights
which may occur as a result of using the contents noted in this manual.
Warranty
Exclusion of loss in opportunity and secondary loss from warranty liability
Regardless of the gratis warranty term, Mitsubishi shall not be liable for
compensation to:
(1) Damages caused by any cause found not to be the responsibility of
Mitsubishi.
(2) Loss in opportunity, lost profits incurred to the user by Failures of Mitsubishi
products.
(3) Special damages and secondary damages whether foreseeable or not,
compensation for accidents, and compensation for damages to products
other than Mitsubishi products.
PLC (4) Replacement by the user, maintenance of on-site equipment, start-up test run
and other tasks.
 This product has been manufactured as a general-purpose part for general
R4-25P GT10-C R2-6P
industries, and has not been designed or manufactured to be incorporated in
GOT
GOT
Untied Untied
(terminal (terminal
a device or system used in purposes related to human life.
wire wire
block) block)
color color  Before using the product for special purposes such as nuclear power, electric
24V 24V
power, aerospace, medicine or passenger movement vehicles, consult with
SDA Brown SD Brown
Mitsubishi Electric.
Red RD Red
SDB
 This product has been manufactured under strict quality control. However
Orange Blue
RDA ER
when installing the product where major accidents or losses could occur if the
RDB Yellow DR Yellow
product fails, install appropriate backup or failsafe functions in the system.
SG Green SG Green
RSA Blue RS Purple
Purple CS
RSB
CSA Black NC
CSB White NC
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
7mm (0.27")
Tightening torque 0.22 to 0.25 N m

SZS 0.4  2.5 (Phoenix Contact Inc.)
Note: This symbol mark is for China only.
产品中有害物质的名称及含量
有害物质
多溴
铅 汞 镉 六价铬 多溴联苯
二苯醚
(Pb) (Hg) (Cd) (Cr(VI)) (PBB)
(PBDE)
外壳 ○ ○ ○ ○ ○ ○
印刷基板 × ○ ○ ○ ○ ○
背光灯
○ × ○ ○ ○ ○
(CCFL)
电缆 × ○ ○ ○ ○ ○
For safe use