MaxiiNet Vi30005 Installation Manual

Vi30005 5-Port 1G PoE Powered PoE Switch Installation Manual
The MaxiCollector Vi30005 is a revolutionary five port 1G Powered PoE
switch. The Vi30005 can accept PoE power from an external source and
provide PoE to all four ports. This eliminates the need for local power
supplies and outlets, and lowers installation costs.
The Vi30005's plug-and-play eliminates the need for IP addressing. The four
Ethernet port can be directly connected to any IP address and will pass that
device's IP address. Network pre-programmed switching features include
802.1p QoS priority queuing, port based VLAN, MAC addressing up to 2K
full and half duplex operation compliant to 802.3x standards and automatic
address learning and aging.
The Vi30005 takes full advantage of high bandwidth maintaining
10/100/1000Mbps transmission with minimum transmission error and
latency by employing full layer 2 network switching technology. The Vi30005
can be used to connect to multiple remote network devices such as
Megapixel IP cameras, VoIP telephone systems, or wireless transmitters.
Using the Vi1120, 120 watt 57 volt power supply, and any MSA compliant
fiber SFP, the Vi30005 can transmit four cameras over distance of 80Km
while providing 30 watts per port and up to 60 watts for two port using the
Vi0015 combining cable.
Important Safety Warning
- Read and keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Install in accordance with the manufacturer's instructions.
- This installation should be made by a qualified service person and should conform to all local
codes.
- DO NOT bundle UTP or Coax signals in the same conduit as high-voltage wiring.
- To reduce the risk of fire or electrical shock, do not expose these products to rain, moisture,
dripping or splashing.
- No objects filled with liquids, such as vases, shall be placed on Vigitron equipment.
- DO NOT install the unit in a place where the operating ambient temperature exceeds 75°C or
is below - 40°C.
- Make sure that the external power supply output voltage is in the recommended range.
- Do not install near any heat sources such as radiators, heat registers, stoves or other
apparatus (including DVRs) that produce heat.
- Protect the power cord from being walked on or pinched particularly at power source,
convenience receptacles, and the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as when a power supply cord or plug is damaged, liquid
has been spilled, objects have fallen inside the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has been dropped.
- The main plug is used as the disconnect device and shall remain readily operable.
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
WARNING! - To reduce the risk of fire or electric shock, do not expose this apparatus to
rain or moisture. This apparatus shall not be exposed to dripping or splashing and no
objects filled with liquids, such as vases shall be placed on the apparatus.
WARNING! - This apparatus is a Class I product. This product must be connected to a
mains socket outlet thru an AC to DC Power supply.
WARNING! - The mains plug is used as the disconnect device and shall remain readily
operable.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The Smart Choice for Transmission Solutions
Application Drawing
Vi3005 powered by 60W PoE Application:
Vi30005
Data & 60W PoE
Vi2202
Vi3326
60W PoE Output w/ Local Power Supply Application:
Vi30005
328 ft. (100m) Cat-5
Vi3326
Vi1120
Fiber Optics w/ Local Power Supply and 30W PoE output Application:
Long Distance Fiber Optics
+
+
Vi3326
SFP SFP
Vi1120
IP Camera-end Installation
UTP Uplink w/ Remote PoE:
- Connect the network cable coming from the PoE switch or PoE midspan
to the fifth Ethernet port at rear of Vi30005.
- Plug in the IP/PoE devices to the four ports one the Vi30005's front panel.
- Set 30W/60W based on the type of the remote PoE source
PoE Power is allocated based on the required port power up to 37W starting with
Port 1 having the highest priority. Once the total sum of the PoE power is allocated
no more power will be available to remaining ports.
UTP Uplink w/ Local Power Supply:
- Connect the network cable coming from the PoE switch or PoE midspan
to the fifth Ethernet port at rear of Vi30005.
- Plug in the IP/PoE devices to the four ports one the Vi30005's front panel.
- Connect the approved local power supply to the power connector of Vi30005.
Fiber SFP Uplink:
Note: The SFP (small format pluggables) must be the same types at both ends of
the fiber cable and must match the fiber cable requirements.
- Plugin the SFP to the SFP socket of Vi30005.
- Connect the fiber cable to the SFP.
- Connect the Vi1120 power supply to the Vi30005 power connector.
Individual ports will be able to provide up to 37W. If more power needed for
approved IP devices use the Vi0015 combination cable to combine two ports.
Starting with ports 1 and 2, connect the IP device to the Ethernet port of the Vi0015
cable.
PoE Switch/PoE Midspan end Installation
UTP link:
- Connect the network cable coming from the Vi30005 Uplink port to one of the
Ethernet ports of the PoE switch or PoE Midspan.
Fiber SFP Link:
- Connect the fiber cable to the SFP port of the network switch.
The SFP must be the same types at both ends of the fiber cable and must match
the fiber cable requirements.
MaxiiNet
PoE Switches
Data
30W PoE
IP Cameras
Data
60W PoE
Data
60W PoE
60W PTZ Domes
Vi30005
Data
30W PoE
IP Cameras
www.vigitron.com
™